Junos
Reply
Visitor
fracjackmac
Posts: 4
Registered: ‎10-11-2009

Re: 100% discount on JUNOS certification exam! Limited Time offer

Jeff,

 

I received the "I Love JUNOS Software" stickers.  Thanks!

 

 

Juniper Networks,

 

THANKS for the Free Training Materials and the Free Exam Voucher!!!

 

I successfully passed the JNO-342 exam and am awaiting my JNCIA-ER certificate.

 

JNCIS-ER and JNCIA-EX are next.

 

 

Thanks again!!!

 

 

vrs

 

--- fjm
New User
navydave
Posts: 1
Registered: ‎12-14-2009
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

Hi,

 

I passed JNCIA-ER and would like some of the stickers.  Thanks.

 

 

Visitor
mundhravinit
Posts: 3
Registered: ‎12-16-2009
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

Hi ,
I have took 2 exams thanks to fasttrack vouchers, and I have passed them thanks to the study materials and free dumps available online . Now I am JNCIA-ER and JNCIS-ER.(with 100% discount).

I  would like to receive the  'I Love JUNOS' stickers ....because I am really lovin it!!

Thanks a lot for introducing this offer!

 

Vinit

Trusted Contributor
jmattan
Posts: 48
Registered: ‎06-16-2008
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

[ Edited ]

Folks,

 

Congratulations on earning Junos based certs!!  We're almost out of stickers so shoot me an email at jmattan@juniper.net and I'll get them in the mail.

 

Thanks,
Jeff

Visitor
MuhammadUsman
Posts: 1
Registered: ‎06-30-2010
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

hi friend

My name is Muhammad Usman Riaz I want to certification in junos like u plz help me i shall be very thankfull to u

regards

Visitor
mundhravinit
Posts: 3
Registered: ‎12-16-2009
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

 
Visitor
mundhravinit
Posts: 3
Registered: ‎12-16-2009
0

Re: 100% discount on JUNOS certification exam! Limited Time offer

Right now 50% discount on JUNOS certification exam can be availed.

for qs/ ans dump pls mail me at mundhravinit@hotmail.com.

 

 

Visitor
ryandavebrigino
Posts: 4
Registered: ‎04-04-2011
0

SRX100 connectivity

Dear All,

 

This is my first time posting a message in JNET and so I apologize if I am in the wrong board.

 

I am currently taking my self study for JNCIA and I am using 1 SRX100 for simulation. I am following the JUNOS Cookbook from Oreilly and I am now in firewall filter part.

 

 

my configuration is all default and my problem is below.

I set-up an IP address 10.1.1.1/24 to fe-0/0/2  and connect my laptop with IP of 10.1.1.2/24

 

root@router1# run show interfaces terse fe-0/0/2
Interface               Admin Link Proto    Local                 Remote
fe-0/0/2                up    up
fe-0/0/2.0              up    up   inet     10.1.1.1/24

 

from the output, I am not sure if I should be seeing the 10.1.1.2/24 under the remote column.

 

but I supposed that by befault. all traffic should be accepted since I did not specidfy any filter.

 

when I ping 10.1.1.1 from my laptop. I am receiving a request time out. but when I execute "arp-a" I can see the

SRX100 fe-0/0/2 mac address registered to my laptop's mac address table.

 

I am not yet good in setting up zones in junos but if you think theres something missing in my test configuration,

I will appreciate any advise to make it work.

 

Thanks

 

-ryan

 

As I undeerstand,

Distinguished Expert
muttbarker
Posts: 2,370
Registered: ‎01-29-2008
0

Re: SRX100 connectivity

You won't see the .2 address under remote. If your ping is failing you probably are running into a security issue. You may want to run the box wide open to start with. I would recommend reading the Juniper Day One guides but in the interim here are a couple of good commands:

 

user@host# set security policies default-policy permit-all <this command allows traffic flow across all security zones>

 

Within a zone you may want to set:

 

user@host# set security zones security-zone ZONENAME host-inbound-traffic system-services all

 

This will allow ALL inbound traffic <pings, ftp....> to the interfaces defined in the zone - or specify the specific traffic types....

 

Feel free to post your config! Also I would HIGHLY recommend you get the JUNOS Security book from O'Reilly and the JUNOS Enterprise Routing book. The cookbook is great but the Security book reflects all the needed material for working the newer flow based JUNOS that now runs and is geared specifically for the SRX solution.

 

Finaly you can run your SRX as a non flow based device and essentially turn off all flow based security by issuing the following command:

 

user@host# set security forwarding-options family mpls mode packet-based

 

Hope this helps you.

 

Kevin Barker
JNCIP-SEC
JNCIS-ENT, FWV, SSL, WLAN
JNCIA-ER, EX, IDP, UAC, WX
Juniper Networks Certified Instructor
Juniper Networks Ambassador

Juniper Elite Reseller
J-Partner Service Specialist - Implementation

If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.
Copyright© 1999-2013 Juniper Networks, Inc. All rights reserved.