SRX Services Gateway
Reply
Contributor
after1
Posts: 69
Registered: ‎06-04-2010
0

SRX240H

Hi,

 

Yes, Im a Cisco man and I'm complete new to Juniper world and I want to covert to Islam - I mean Juniper :smileytongue:.

 

Anyway, I understand that the srx240 comes with fixed 16 x 10/100/1000BASE-T ports. Are these switchports only? Does SRX240 supports routing and switching?? To enable routing on the box, must I use the SFP PIM?

 

Thanks everyone who response.

Trusted Contributor
mwdmeyer
Posts: 196
Registered: ‎03-11-2008

Re: SRX240H

All 16 ports can be used for routing or switching, would be pretty bad if it didn't! :smileytongue:

Contributor
after1
Posts: 69
Registered: ‎06-04-2010
0

Re: SRX240H

[ Edited ]

Excellent. How many SFP does the box supports? I want to install 4 SFPs on thebox, is it possible?

Trusted Expert
Automate
Posts: 784
Registered: ‎11-01-2007
0

Re: SRX240H

[ Edited ]

@after1 - you asked for "AND" and the reply said "OR" - do you need routing AND switching (bridging)? (IRB?)

 

Thx,

 

-Keith

Trusted Contributor
BenR
Posts: 89
Registered: ‎03-18-2010
0

Re: SRX240H

Just a heads up - the SFP slots only support 100 Mbps throughput, even if you use a Gigabit Ethernet SFP. Tell your Juniper Rep how stupid you think this is, please!

 

Info from the SFP Mini-PIM datasheet http://www.juniper.net/us/en/local/pdf/datasheets/1000315-en.pdf and JTAC.

Contributor
after1
Posts: 69
Registered: ‎06-04-2010
0

Re: SRX240H

Gotta be kidding me.

 

What's the point of getting SFP then.

 

IS SRX240H support voip? e.g cme equipvalent.

Super Contributor
colemtb
Posts: 313
Registered: ‎09-30-2009
0

Re: SRX240H

[ Edited ]

BELIEVE / THINK <- not 100% sure...... there will be support for voice systems / SIP; but...  yes, more CME, not CME / CUE.  I don't believe VM is built in, but AA, FXO, FXS, and sip will be options.  SRST-style?

 

I think this is an ICS 240 too, not sure if DSPs will be built to PIMs or not...

Distinguished Expert
rkim
Posts: 755
Registered: ‎11-06-2007
0

Re: SRX240H

The 100 Mbps limit is due to bus connection limitation for mPIM slots. The mPIMs are same ones used on SSG20 as well as SRX210 models which normally would only use mPIM for WAN type connections (i.e. T1, DSL, Cable). So the 100Mbps bus connection is more than adequate for these types of mPIMs. The SFP mPIM merely gives you an option for those customers that require fiber connection. But of course if you require GE speeds, the SRX240 has 16 copper ports which I think should meet needs. 

 

And yes, you can configure each onboard port to be routed or switched. In fact, if just switching (not requiring any routing) then you can get line rate on each GE port. You can mix and match as you please with the onboard ports.

 

-Richard

Visitor
Haitham
Posts: 5
Registered: ‎05-18-2008
0

Re: SRX240H

If you run 2 SRX240 in cluster mode. Switchport is not supported and you must use each port in routing mode.

 

Haitham

Copyright© 1999-2013 Juniper Networks, Inc. All rights reserved.