SRX Services Gateway
Reply
Contributor
Zhoukangle
Posts: 92
Registered: ‎02-22-2011
0

show the NPU information

HI,all,

I want to show the information of NPU on srx3600,which command should I use?thank you.

Recognized Expert
rasmus
Posts: 377
Registered: ‎02-28-2010
0

Re: show the NPU information

 
Hafiz Muhammad Farooq
JNCIE-SEC, JNCIP-SEC, JNCIS-SEC, JNCIS-FWV
JNCIS-SP, JNCIS-SA, JNCIA-JUNOS
IBM Qradar Deployment Professional

[Please mark it as Accepted Solution if it works, Kudos if you like]

Juniper Employee
rayado
Posts: 51
Registered: ‎04-26-2010
0

Re: show the NPU information

What specifically were you looking for? Here are some commands to verify NPC status and connectivity with the other modules:

 

{primary:node0}
root@SRX-R1> show chassis ioc-npc-connectivity                  
IOC  IOC type    IOC state      Connected NPC  NPC state      Link status
0    SFB 12GE    Online         10             Online         Up        
2    16xGE SFP   Online         11             Online         Up        
5    16xGE SFP   Offline        10             Online         Down      

{primary:node0}
root@SRX-R1> show chassis fpc pic-status
node0:
--------------------------------------------------------------------------
Slot 0   Online       SRX3k SFB 12GE
  PIC 0  Online       8x 1GE-TX 4x 1GE-SFP
Slot 2   Online       SRX3k 16xGE SFP
  PIC 0  Online       16x 1GE-SFP
Slot 5   Offline      SRX3k 16xGE SFP
Slot 7   Online       SRX3k SPC
  PIC 0  Online       SPU Cp-Flow
Slot 8   Online       SRX3k SPC
  PIC 0  Online       SPU Flow
Slot 9   Online       SRX3k SPC
  PIC 0  Online       SPU Flow
Slot 10  Online       SRX3k NPC
  PIC 0  Online       NPC PIC
Slot 11  Online       SRX3k NPC
  PIC 0  Online       NPC PIC

{primary:node0}
root@SRX-R1> show chassis fpc 11 detail
node0:
--------------------------------------------------------------------------
Slot 11 information:
  State                                 Online   
  Temperature                        37 degrees C / 98 degrees F
  Total CPU DRAM                   1024 MB
  Total RLDRAM                        0 MB
  Total DDR DRAM                      0 MB
  Start time:                           2011-07-13 17:05:15 CDT
  Uptime:                               30 days, 1 hour, 52 minutes, 11 seconds
  Max Power Consumption               0 Watts

{primary:node0}
root@SRX-R1> show chassis fabric plane  
node0:
--------------------------------------------------------------------------
Fabric management PLANE state
Plane 0
  Plane state: ACTIVE
      FPC 0
          PFE 0 :Links ok
      FPC 2
          PFE 0 :Links ok
      FPC 7
          PFE 0 :Links ok
      FPC 8
          PFE 0 :Links ok
      FPC 9
          PFE 0 :Links ok
      FPC 10
          PFE 0 :Links ok
          PFE 1 :Links ok
      FPC 11
          PFE 0 :Links ok
          PFE 1 :Links ok

Contributor
Zhoukangle
Posts: 92
Registered: ‎02-22-2011
0

Re: show the NPU information

hi,rayado,

thank you for your response,and more command for the Utilization of NPU?thank you.

Copyright© 1999-2013 Juniper Networks, Inc. All rights reserved.