Screen OS

last person joined: 8 months ago 

This is a legacy community with limited Juniper monitoring.

  • 1.  manual speed settings on interface module on SSG320M

    Posted 05-08-2012 02:28

    Hi,

     

    We have a SSG320M firewall device running 6.3 Or 3.0 version of firmware. We have inserted a 6 interface module slot on the firewall slot 1(from eth1/0 to eth1/5).

     

    Now, we need to set the interface speed on interface eth1/0 to eth1/5, but I am not able to do so.

    When I try to do through CLI, I see only these options:

    auto

    link-down

    manual

     

    I use command: set interface eth1/1 phy ?

     

    I want to confirm if it is possible to manually configure speed on interfaces.



  • 2.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 02:35

    Hi,

     

    Maybe this link helps: http://www.juniper.net/techpubs/en_US/junos/topics/topic-map/mcast-bandwidth-mgmt.html



  • 3.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 02:55

    Hi Stac,

     

    Thanks for the reply.

    I guess the document that you gave is to manually configure the BW on interface and that too on JUNOS.

     

    What my question is, I have inserted a module of 6 gig interfaces in the firewall SSG320 with ScreenOS. Can we manually set speed to 100MB on new interfaces with duplex settings?



  • 4.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 03:40

    This is an interface command parameter.

     

    set int e1/6 phy full 100mb

     



  • 5.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 03:59

    Hi, this command does not work on module.

     

    XXXX-Cluster:XXXX-FW01(M)-> set interface eth1/5 phy 1000
                                                              ^------unknown keyword 1000



  • 6.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 04:08
    Add the mb to the parameter "1000mb" You can always use the ? To get a listing of the correct completions when you get this message. set interface eth1/5 phy ?


  • 7.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 04:34

    XXXX-Cluster:XXXX-FW01(M)-> set interface eth1/5 phy 1000mb
                                                      ​        ^------unknown keyword 1000mb

     

    when I do ? after "phy" command, it gives options

    auto

    link-down

    manual

     



  • 8.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 05:11
    Ok. What about

    set interface eth1/5 phy manual ?


  • 9.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 05:54

    Hi,

     

    Have you already inserted the optical/cooper transceiver SFP modules?

     



  • 10.  RE: manual speed settings on interface module on SSG320M

    Posted 05-08-2012 06:53

    set interface eth1/5 phy manual ?

     

    Nothing after manual option. just an enter

     

    Yes, all the connecitons are done. FW is in production.



  • 11.  RE: manual speed settings on interface module on SSG320M

    Posted 05-09-2012 06:03

    Hi,

     

    Not all optical transeivers/ports support manual settings. This might also be a module or ScreenOS limitation. If you see no CRC/Alignment etc. errors, the Auto mode is running fine.



  • 12.  RE: manual speed settings on interface module on SSG320M
    Best Answer

     
    Posted 05-16-2012 19:18

    We can't set speed on optical interfaces in Screen OS, hence you are not getting those options for speed settings !