ScreenOS Firewalls (NOT SRX)
Reply
Visitor
wayneatwood
Posts: 7
Registered: ‎08-26-2009
0
Accepted Solution

ssg5 - new post cause...

I mistakenly marked the last one solved :-(                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       My internet is all blocked up, hammer up and using all of the band width.

Could it be the ssg5? 

 

 

 

I was asked for the session count and resource utilization? Where would I find that information? Wayne

 

 

I mistakenly marked the last one solver :-(

 

 

 

 

 

 

 

Distinguished Expert
muttbarker
Posts: 2,346
Registered: ‎01-29-2008

Re: ssg5 - new post cause...

The "get session" command from the cli will show you sessions and total session count. The "get performance cpu" command gives you utilization rates.
Kevin Barker
JNCIP-SEC
JNCIS-ENT, FWV, SSL, WLAN
JNCIA-ER, EX, IDP, UAC, WX
Juniper Networks Certified Instructor
Juniper Networks Ambassador

Juniper Elite Reseller
J-Partner Service Specialist - Implementation

If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.
Visitor
wayneatwood
Posts: 7
Registered: ‎08-26-2009
0

ssg5 internet hammered up

 

 

 

 

My internet is blocked up or hammered up meaning using all of the band width.

Could it be the ssg5?  I ran get session and get performance cpu: attached                                                                                                                                                                                                                                                                                                                                Wayne                                                                                            

Distinguished Expert
muttbarker
Posts: 2,346
Registered: ‎01-29-2008
0

Re: ssg5 internet hammered up

[ Edited ]

Well the box is certainly not working to hard :smileyhappy: The CPU, etc are pretty idle. So the SSG is not the culprit.

 

Perhaps you have some big user downloads chewing up your bandwidth? You can turn on traffic shaping and see what bandwidth you are using. I am heading into a meeting so can't pull out the commands but go to the admin guide and look for traffic shaping. You set max in and out bandwidth on the I/F's in question - enable traffic shaping (cli command I recall) and then you can look at statistics through the GUI and through the cli. GUI is under reports. CLI commands involve the "traffic-shaping" value.

 

So look at "get traffic-shaping" - "set traffic-shaping" etc......

 

Both the cli and the gui will end up showing you actual bandwidth usage - cli has a ton of data - i think the syntax for seeing it "get traffic-shaping statistics" but make sure you enable it with the get command.

Message Edited by muttbarker on 08-28-2009 07:55 AM
Kevin Barker
JNCIP-SEC
JNCIS-ENT, FWV, SSL, WLAN
JNCIA-ER, EX, IDP, UAC, WX
Juniper Networks Certified Instructor
Juniper Networks Ambassador

Juniper Elite Reseller
J-Partner Service Specialist - Implementation

If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.
Visitor
wayneatwood
Posts: 7
Registered: ‎08-26-2009
0

Re: ssg5 - new post cause...

 

 

In telnet what command runs enable traffic-shaping? <get> doesn't work. 

Distinguished Expert
muttbarker
Posts: 2,346
Registered: ‎01-29-2008
0

Re: ssg5 - new post cause...

Hopefully you got this figured out. The command is "get traffic-shaping interface I/F-Name"
Kevin Barker
JNCIP-SEC
JNCIS-ENT, FWV, SSL, WLAN
JNCIA-ER, EX, IDP, UAC, WX
Juniper Networks Certified Instructor
Juniper Networks Ambassador

Juniper Elite Reseller
J-Partner Service Specialist - Implementation

If this worked for you please flag my post as an "Accepted Solution" so others can benefit. A kudo would be cool if you think I earned it.
Copyright© 1999-2013 Juniper Networks, Inc. All rights reserved.