07-28-2011 03:16 PM
I am preparing for the JNCIE-ENT lab exam so is there any idea what is the hardware that it will be used in the lab exams and the JUNOS version , also i have mentions that NAT and IPSEC not in the JNCIE-ENT Blueprint any more ( it was part of JNCIE-ER ) so it will not be in the exam ??
Thanks a lot
11-27-2011 08:01 PM
All is about routing and switching. i just passed few months ago...don't worry !! Juniper loves asking the default, drive me crazy...but still love its commit command
01-02-2012 11:45 PM
Any idea if there will be T1/E1 interfaces involved at all or will the exam purely be ethernet, looking at the exam topics it seems to indicate that i should not expect to see frame-relay or ppp at all. also is the exam absolutely confined to the topics listed in the link below or are the subjects listed an indication of what may be tested on but not limited to.
01-02-2012 11:55 PM
Also what study material are you guys using? seeing how there is no JNCIE study guides or practice labs i have been working off the juniper courseware AJEX & AJER an the O'reilly enterprise Routing & switching books, these 4 books do appear to cover pretty much most of the subjects listed in the exam topics but was wondering if there was anyting else you guys recommend that would give me an extra edge in passing the exam?
01-03-2012 02:07 AM
I passed my exam by only using Fast Track program books and lecture. However, I have background as CCIP in Cisco world. So what i needed to know was to commands and features that included in EX series switches. BGP best selection has some differences comparing to Cisco's. O'reilly enterprise Routing & switching would be more than enough to pass the JNCIS-ENT exam. Rember: Default features are needed to remember, my experience
Good Luck !
05-02-2012 12:47 AM
IPV6Freely, how did you study the OSPF MTR subject? i have SRX 210's and 240's in my lab running Junos 10.4R9.2 and i cannot configure the MTR feature under ospf or the routing-options (see error below), I have an M7i which I can configure it on, do you know where i can track down some documentation on how to configure MTR's on the SRX platform (assuming it is even possible on the platform at all) so that i can make sure i know it for the exam
root@SRX2# show protocols ospf
## Warning: statement ignored: unsupported platform (srx240h)
## topology red;
Other than MTR's the only other thing i'm having problems finding good documentation on is "Load Balancing Hash Flow", most of the documentation i can find about this seem to be more relevant to the MX platform and MPLS, but cannot find anything that sounds even remotly close to being relevant to the SRX's and enterprise networks, I dont suppose you know where i can also find some documentation about this subject taht is relevant to the exam?
05-09-2012 07:32 PM
So I found the documentation I was after regarding "Load Balancing Hash Flow" in the JNCIS-ENT study guide that is available through the Juniper Fast track program, so all sorted in regards to that subject.
As for the MTR subject I am still a bit puzzeled regarding this feature, I saw another post that IPV6Freely made saying that the exam has a combination of SRX240's and EX4200's running Junos 10.4, if this is the case I cannot see how this feature can be tested at all unless I am missing something completly obvious
05-21-2012 09:09 PM
I asked a similar question about the support of MTR on SRX's in the SRX forum, no one answered that post either, what i suspect (and this is 100% speculation), is that even tho it says "MTR", MTR might have been put in the list when the exam was being developed, I have read in a few books that the low end M series (such as the M7i) are designed for service providers and large enterprises, the M series support MTR, there may have been an initial intention to throw in a M7i in the mix, however this may have made things tricky because the QOS schedulers work differently on the M series and the SRX's, what they may actually test you on is something like multi instance OSPF with firewall based forwarding and using rib groups to import routes between instances, this would allow them create similar scenarios to what they could have tested you with MTR.
10-20-2012 04:35 PM
MTR is not supported on the SRX platform, so this blueprint topic can be ignored. I've already contacted the Juniper certification team to have it removed. See: http://pathfinder.juniper.net/feature-explorer/fea
Former CCIE #25655
Former Juniper Ambassador