SRX

Hi All,

I have a problem with my srx 240, it cannot load the junos even I reboot repeatedly, it always prompt

loader>

and I try to install via loader using loader>install file:///<srx image>

it always failed and stops installation

here's the log

Trying to mount root from cd9660:/dev/md0

WARNING: preposterous time in file system

WARNING: clock 8323 days greater than file system time

tty: not found

Installing disk1:/junos-srxsme-10.1R1.8-domestic_2.tgz

mount_msdosfs: /dev/da1s1: No such file or directory

ERROR: Execution failed for command mount

Anyone experience with this case?

Please advice

Thanks and Regards,

Husni

It will be helpful to find the cause of the problem if you paste the whole log right from the u-boot coming up.

Regards

Hi amjain,

Thanks for the reply

Here's the logs that you requested

loader> install file:///junos-srxsme-10.1R1.8-domestic_2.tgz
/kernel data=0x93b174+0xc7268 syms=[0x4+0x75fa0+0x4+0xa7388]
Kernel entry at 0x801000d8 ...
getbootinfo: magic 0x0 md 0x817c7000 memsize 0x0
getbootinfo: boothowto 0x0 kernend 0x81800000 memsize 1024MB kernelname /kernel

Platform Starting
init regular console
Initializing octeon watchdog
GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
getmemsize: msgbufp[size=32768] = 0x8000cfe4
Copyright (c) 1996-2010, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
JUNOS 10.1R1.8 #0: 2010-02-12 18:31:54 UTC
    builder@queth.juniper.net:/volume/build/junos/10.1/release/10.1R1.8/obj-octeon/bsd/sys/compile/JSRXNLE
JUNOS 10.1R1.8 #0: 2010-02-12 18:31:54 UTC
    builder@queth.juniper.net:/volume/build/junos/10.1/release/10.1R1.8/obj-octeon/bsd/sys/compile/JSRXNLE
real memory  = 1073741824 (1024MB)
avail memory = 519200768 (495MB)
cpuid: 0, btlb_cpumap:0xffffffff
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
Initializing watchdog interupt

Loading RT Fifo module.....
Loaded RT Fifo module
pmap_helper loaded (interface version 6, syscall 210)
cpu0 on motherboard
: CAVIUM's Octeon CPU Rev. 0.8 with no FPU implemented
        L1 Cache: I size 32kb(128 line), D size 8kb(128 line), sixty four way.
        L2 Cache: Size 128kb, ? way
obio0 on motherboard
uart0: <Octeon-16550 channel 0> on obio0
uart0: console (9600,n,8,1)
twsi0 on obio0
dwc0: <Synopsis DWC OTG Controller Driver> on obio0
usb0: DWC OTG Controller 
Using DMA mode
Init: Port Power? op_state=1
Init: Power Port (0)
usb0: <USB Bus for DWC OTG Controller> on dwc0
usb0: USB revision 2.0
uhub0: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1: vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 2
uhub1: single transaction translator
uhub1: 3 ports with 2 removable, self powered
umass0: STMicroelectronics ST72682  High Speed Mode, rev 2.00/2.10, addr 3
umass1: Imation UFDASKY2G, rev 2.00/1.00, addr 4
dwc1: <Synopsis DWC OTG Controller Driver> on obio0
usb1: DWC OTG Controller 
Using DMA mode
Init: Port Power? op_state=1
Init: Power Port (0)
usb1: <USB Bus for DWC OTG Controller> on dwc1
usb1: USB revision 2.0
uhub2: vendor 0x0000 DWC OTG root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 1 port with 1 removable, self powered
pcib1: <Cavium on-chip PCIe HOST bridge> on obio0
Disabling Octeon big bar support
PCIe: Waiting for port 0 to finish reset
PCIe: Port 0 link active, 2 lanes
PCIe: Waiting for port 1 to finish reset
PCIe: Port 1 link active, 1 lanes
pcib1: Initialized controller
pci0: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 0.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <serial bus, USB> at device 2.0 (no driver attached)
pci1: <network> at device 7.0 (no driver attached)
pcib0: <Cavium on-chip PCIe HOST bridge> on obio0
pci2: <PCI bus> on pcib0
pci2: <processor> at device 0.0 (no driver attached)
cpld0 on obio0
gblmem0 on obio0
octpkt0: <Octeon RGMII> on obio0
cfi0: <AMD/Fujitsu - 4MB> on obio0
platform_cookie_read not implemented
Timecounter "mips" frequency 600000000 Hz quality 0
Timecounters tick every 1.000 msec
fxp_ctrlif_attach:fxpctrldev = c1c7b000
fxp2_ctrlif_attach:fxpctrldev = 0xc1c7b000
Loading the NETPFE ethernet module
Loading E1/T1/J1 driver
Loading the DS1/E1 Media Layer; Attaching to media services layer
Loading common multilink module.
Loading the NETPFE PPPoE module
Loading the netpfe services driver
Loading the NETPFE docsis module
Loading the XDSL Media Layer; Attaching to media services layer
Loading the IPSec driver
 Loading the PTM driver

Loading the DIALER driver
Loading Link Services PICs module.
IPsec: Initialized Security Association Processing.
md0: Preloaded image </isofs-install-srxsme> 12216320 bytes at 0x80c1f70c
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!


SMP: AP CPU #3 Launched!
da1 at umass-sim1 bus 1 target 0 lun 0
da1: <Imation UFDASKY2G 1.20> Removable Direct Access SCSI-2 device 
da1: 40.000MB/s transfers
da1: 1928MB (3948544 512 byte sectors: 255H 63S/T 245C)
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device 
da0: 40.000MB/s transfers
da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C)
if_pfe_open: listener socket opened, listening on ...
Trying to mount root from cd9660:/dev/md0
WARNING: preposterous time in file system
WARNING: clock 8323 days greater than file system time
tty: not found
Installing disk1:/junos-srxsme-10.1R1.8-domestic_2.tgz
mount_msdosfs: /dev/da1s1: No such file or directory
ERROR: Execution failed for command mount
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `vnlru_mem' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...1 0 done

syncing disks... All buffers synced.
Uptime: 12s
Rebooting...
cpu_reset: Stopping other CPUs


U-Boot 1.1.6 (Build time: Feb 12 2010 - 18:06:25)

SRX_240_HIGHMEM board revision major:0, minor:31, serial #: AAAM9182
OCTEON CN5230R-SCP pass 2.0, Core clock: 600 MHz, DDR clock: 333 MHz (666 Mhz data rate)
DRAM:  1024 MB
Starting Memory POST... 
Checking datalines... OK
Checking address lines... OK
Checking 512K memory for U-Boot... OK.
Running U-Boot CRC Test... OK.
Flash:  4 MB
USB:   scanning bus for devices... 
Root Hub 0: 4 USB Device(s) found
Root Hub 1: 1 USB Device(s) found
       scanning bus for storage devices... 2 Storage Device(s) found
Clearing DRAM........ done
BIST check passed.
1:00:00.0 Vendor/Device ID = 0x811210b5
1:01:07.0 Vendor/Device ID = 0xc72414e4
Boot Media: nand-flash usb 
Net:   octeth0
POST Passed
Press SPACE to abort autoboot in 1 seconds
ELF file is 32 bit
Loading .text @ 0x8f000078 (242432 bytes)
Loading .rodata @ 0x8f03b378 (13908 bytes)
Loading .rodata.str1.4 @ 0x8f03e9cc (15956 bytes)
Loading set_Xcommand_set @ 0x8f042820 (100 bytes)
Loading .rodata.cst4 @ 0x8f042884 (20 bytes)
Loading .data @ 0x8f043000 (5584 bytes)
Loading .data.rel.ro @ 0x8f0445d0 (120 bytes)
Loading .data.rel @ 0x8f044648 (136 bytes)
Clearing .bss @ 0x8f0446d0 (8560 bytes)
## Starting application at 0x8f000078 ...
Consoles: U-Boot console  
Found compatible API, ver. 1.7

FreeBSD/MIPS U-Boot bootstrap loader, Revision 1.7
(builder@queth.juniper.net, Fri Feb 12 18:14:30 UTC 2010)
Memory: 1024MB
[8]Booting from nand-flash slice 2
Un-Protected 1 sectors
writing to flash...
Protected 1 sectors
Autoboot abort requested, entering loader prompt.

Type '?' for a list of commands, 'help' for more detailed help.
loader> 
loader> 
loader> 
loader> 
loader> 

Thanks and Regards,

Husni

This is a strange problem. JUNOS while trying to install the package is not able to read the partition (/dev/da1s1) on the USB key holding the package to install.

You may want to try out the following steps as per your convenience:

Step 1:

    * Take another USB key (preferably of the make Transcend, Kingston, Lexar, Unigen or Sandisk) and format it.

    * Use FAT if USB key is of size is less than equal to 2GB or FAT32 if USB key size is greater than or equal to 4 GB. 

    * Copy the package junos-srxsme-10.1R1.8-domestic_2.tgz in root directory of USB key

    * Try install from loader prompt using command install file:///junos-srxsme-10.1R1.8-domestic_2.tgz

Step 2:

    If you do not have any other USB key then use the following procedure for the USB key you are using till now  (which as log messages show is 2GB Imation USB key)

    * Format using FAT as size of USB key is 2GB  

    * Copy the package junos-srxsme-10.1R1.8-domestic_2.tgz in root directory of USB key

    * Try install from loader prompt using command install file:///junos-srxsme-10.1R1.8-domestic_2.tgz

Hi amjain,

Thanks for your reply, I've tried all the steps and sadly failed.

I try to contact JTAC, but still no response.

Thanks and Regards,

Husni