Switching

I can login in the linux shell, but I can't start junos, somebody knows how it start or commands to load it?

GNU GRUB version 2.02~beta2+e4a1fe391

+----------------------------------------------------------------------------+
|*Juniper Linux |
| Juniper Linux Debug |
| Juniper-Linux-Recovery |
| Go to ONIE Loader |
+----------------------------------------------------------------------------+

i8042: No controller found
First Level Bootstrap using initramfs...
sd 6:0:0:0: [sdb] No Caching mode page found
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] No Caching mode page found
sd 6:0:0:0: [sdb] Assuming drive cache: write through
sd 6:0:0:0: [sdb] No Caching mode page found
sd 6:0:0:0: [sdb] Assuming drive cache: write through
Mounting boot device LABEL=LINUX-BOOT
Unpacking initrd.cpio.gz ....
774557 blocks
Unmount boot device LABEL=LINUX-BOOT
INIT: version 2.88 booting
Starting udev
running pre rc steps on Rangeley
2 logical volume(s) in volume group "vg0_vjunos" now active
Starting udev
Starting Bootlog daemon: bootlogd.
Populating dev cache
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
kernel.core_uses_pid = 0
kernel.core_pattern = |/etc/init.d/zipcore.sh /var/tmp/corefiles/ %h.%e.%p.%t.core %e
fs.suid_dumpable = 2
vm.swappiness = 1
vm.vfs_cache_pressure = 50
Starting atd: OK
INIT: Entering runlevel: 3
Starting system message bus: dbus.
Starting OpenBSD Secure Shell server: sshd
done.
Configuring network interfaces... done.
Starting domain name service: named.
Starting irqbalance: done
Starting ntpd: done
starting rsyslogd ... done
Starting internet superserver: xinetd.
* Starting virtualization library daemon: libvirtd
no /usr/bin/dnsmasq found; none killed
2016-07-16 06:39:22.164+0000: 983: info : libvirt version: 1.1.2
2016-07-16 06:39:22.164+0000: 983: warning : virGetHostname:625 : getaddr[ ok ]ailed for 'dhcp-10-1-1-105': Name or service not known
Starting crond: OK
Instantiate I2C devices...
i2c i2c-1: Failed to register i2c client pca9548 at 0x70 (-16)
Bring up system as SNX60A0-486F (0x0011)
/etc/rc3.d/S90rc.i2cinit: line 100: echo: write error: Invalid argument
i2c i2c-4: Failed to register i2c client 24c128 at 0x56 (-16)
/etc/rc3.d/S90rc.i2cinit: line 116: echo: write error: Invalid argument
adt7470 12-002c: cannot read configuration register
Instantiate GPIO devices...
od: /sys/bus/i2c/devices/17-0056/eeprom: read error: Connection timed out
Booting normal on Rangeley
/root: 60.5 MiB (63457280 bytes) trimmed
/var: 13.4 MiB (14073856 bytes) trimmed
/app_disk: 1.9 MiB (1940480 bytes) trimmed
od: /sys/bus/i2c/devices/17-0056/eeprom: read error: Connection timed out
Executing application: pkg-app-junos
Initializing JUNOS Host applications
[ OK ] Application initialization.
Stopping internet superserver: xinetd.
Starting internet superserver: xinetd.
net.ipv4.ip_forward = 1
Stopping Bootlog daemon: bootlogd.
Starting tcf-agent: OK

Wind River Linux 6.0.0.21 dhcp-10-1-1-105 console

dhcp-10-1-1-105 login: root
Password:
Last login: Sat Jul 16 05:51:23 UTC 2016 from 10.1.1.130 on pts/0
root@dhcp-10-1-1-105:~#

Please refer below links :

http://www.juniper.net/techpubs/en_US/junos14.1/topics/reference/command-summary/start-shell.html

Thanks

Amit

He's already in the shell, he's asking how to enter Juniper CLI. That done with the cli command.

root@test:RE:0% cli

{master:0}

root@test>

This procedure should work, please check: 

https://www.juniper.net/documentation/en_US/junos/topics/task/configuration/authentication-root-password-recovering-qfx-series.html

If none works, try USB recovery to re-install Junos afresh, but you'll lose the config.

Hope this helps.

Regards,
-r.

--------------------------------------------------

If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated :).