Junos
Highlighted
Junos

problem with pppoe configuration

‎01-04-2017 12:21 AM

Hi team,

 

I have a strange problem with a SRX110H2-VA, i connected the fe-0/0/1 to a bridge modem.

i needed to configure a pppoe connection to establish the connection, that works the session is up

i can see the public ip address when i use the following command :

 

root@FWUTD01> show interfaces pp0.0
  Logical interface pp0.0 (Index 76) (SNMP ifIndex 534)
    Flags: Point-To-Point SNMP-Traps 0x0 Encapsulation: PPPoE
    PPPoE:
      State: SessionUp, Session ID: 3862,
      Session AC name: lns-1-lyo-se600, Remote MAC address: 00:30:88:1d:d2:4e,
      Configured AC name: None, Service name: None,
      Auto-reconnect timeout: Never, Idle timeout: Never,
      Underlying interface: fe-0/0/1.0 (Index 75)
      Ignore End-Of-List tag: Disable
    Input packets : 645
    Output packets: 153
  Keepalive settings: Interval 10 seconds, Up-count 1, Down-count 3
  Keepalive: Input: 0 (never), Output: 135 (00:00:07 ago)
  LCP state: Opened
  NCP state: inet: Opened, inet6: Not-configured, iso: Not-configured, mpls: Not-configured
  CHAP state: Success
  PAP state: Closed
    Security: Zone: Internet
    Allowed host-inbound traffic : bootp bfd bgp dns dvmrp igmp ldp msdp nhrp ospf pgm pim rip router-discovery rsvp sap vrrp dhcp finger ftp tftp ident-reset http https ike netconf ping reverse-telnet reverse-ssh rlogin rpm rsh snmp
    snmp-trap ssh telnet traceroute xnm-clear-text xnm-ssl lsping ntp sip r2cp webapi-clear-text webapi-ssl
    Protocol inet, MTU: 1470
      Flags: Sendbcast-pkt-to-re, User-MTU, Negotiate-Address
      Addresses, Flags: Kernel Is-Preferred Is-Primary
        Destination: 178.32.37.4, Local: 109.190.121.60

the problem is i cannot ping this address even i autorized in the the security zones :

        security-zone Internet {
            host-inbound-traffic {
                system-services {
                    all;
                }
                protocols {
                    all;
                }
            }
            interfaces {
                fe-0/0/0.0 {
                    host-inbound-traffic {
                        system-services {
                            all;
                        }
                    }
                }
                fe-0/0/1.0 {
                    host-inbound-traffic {
                        system-services {
                            all;
                        }
                        protocols {
                            all;
                        }
                    }
                }
                pp0.0 {
                    host-inbound-traffic {
                        system-services {
                            all;

and i don't see the ip address on the physical interface fe-0/0/1

is it normal ?

do yo have a solution ?

I configured a dnat rules to access different servers behind that wan access.

 

Thanks for your help.

 

Regards,

David

2 REPLIES 2
Highlighted
Junos

Re: problem with pppoe configuration

‎01-04-2017 12:43 AM

I can ping the public ip address from the internal network.

David

Highlighted
Junos

Re: problem with pppoe configuration

‎01-12-2017 09:08 AM

and i don't see the ip address on the physical interface fe-0/0/1 is it normal ? yes it is normal.

Feedback