SRX Services Gateway
Highlighted
SRX Services Gateway

Unable to find option to configure ADSL2+ on SRX110-va

‎09-18-2019 04:25 AM

Trying to configure PPPoA configure BT ADSL+.

 

But I cannot find the option of  "encapsulation atm-pvc". Any reason why ? 

 

root@xxx# set interfaces pt-1/0/0 encapsulation ?
Possible completions:
ether-vpls-ppp Ethernet VPLS over PPP (bridging) device
extended-frame-relay-ccc Any Frame Relay DLCI for cross-connect
extended-frame-relay-tcc Any Frame Relay DLCI for translational cross-connect
frame-relay-port-ccc Frame Relay port encapsulation for a cross-connect
[edit]

 

 

root@xxx> show chassis hardware
Hardware inventory:
Item Version Part number Serial number Description
Chassis xxxx SRX110H2-VA
Routing Engine REV 02 650-048782   xxxx RE-SRX110H2-VA
FPC 0 FPC
PIC 0 8x FE Base PIC
FPC 1 FPC
PIC 0 Internal VDSL2/ADSL-POTS
Power Supply 0

Juniper release is at 

 

JUNOS Software Release [12.1X44-D35.5]

 

4 REPLIES 4
Highlighted
SRX Services Gateway

Re: Unable to find option to configure ADSL2+ on SRX110-va

‎09-18-2019 04:51 AM

Hello,

 

Since you are using an ADSL interface should you be using interface at-0/0/0.0

 

http://junosnotes.blogspot.com/2012/09/srx-adsl.html

https://networkinferno.net/juniper-srx110-and-adsl

 

I hope this helps. Regards,

 

Vikas

 

Highlighted
SRX Services Gateway

Re: Unable to find option to configure ADSL2+ on SRX110-va

‎09-18-2019 05:56 AM

Hi Vikas,

 

I don't see at interface on device.

 

root@xxx> show interfaces terse
Interface Admin Link Proto Local Remote
fe-0/0/0 up down
fe-0/0/0.0 up down eth-switch
gr-0/0/0 up up
ip-0/0/0 up up
lsq-0/0/0 up up
lt-0/0/0 up up
mt-0/0/0 up up
sp-0/0/0 up up
sp-0/0/0.0 up up inet
sp-0/0/0.16383 up up inet 10.0.0.1 --> 10.0.0.16
10.0.0.6 --> 0/0
128.0.0.1 --> 128.0.1.16
128.0.0.6 --> 0/0
fe-0/0/1 up down
fe-0/0/1.0 up down eth-switch
fe-0/0/2 up down
fe-0/0/2.0 up down eth-switch
fe-0/0/3 up down
fe-0/0/3.0 up down eth-switch
fe-0/0/4 up down
fe-0/0/4.0 up down eth-switch
fe-0/0/5 up down
fe-0/0/5.0 up down eth-switch
fe-0/0/6 up down
fe-0/0/6.0 up down eth-switch
fe-0/0/7 up down
fe-0/0/7.0 up down inet 192.168.10.1/24
pt-1/0/0 down down
pt-1/0/0.0 up down inet
gre up up
ipip up up
irb up up
lo0 up up
lo0.16384 up up inet 127.0.0.1 --> 0/0
lo0.16385 up up inet 10.0.0.1 --> 0/0
10.0.0.16 --> 0/0
128.0.0.1 --> 0/0
128.0.0.4 --> 0/0
128.0.1.16 --> 0/0
lo0.32768 up up
lsi up up
mtun up up
pimd up up
pime up up
pp0 up up
ppd0 up up
ppe0 up up
st0 up up
st0.0 up down inet 10.1.1.11/24
inet6 fe80::42a6:770f:fc2b:97c0/64
st0.254 up down inet 10.0.0.11/24
tap up up
vlan up up
vlan.1 up down inet 10.10.11.1/24

Highlighted
SRX Services Gateway

Re: Unable to find option to configure ADSL2+ on SRX110-va

‎09-18-2019 06:22 AM

Hello,

 

I suggest you proceed with the configuration on at-1/0/0 and commit the same. It may take a min to reflect the same.

 

Please refer to: https://www.juniper.net/documentation/en_US/junos/topics/topic-map/security-interface-configuring-vd...

 

> VDSL2 Interface Compatibility with ADSL Interfaces:

> On VDSL2 interfaces, by default the pt-1/0/0 interface is created when there is no configuration already created for either the pt-1/0/0 or the at-1/0/0 interface
> It requires around 60 seconds to switch from VDSL2 to ADSL or from ADSL to VDSL2 operating modes

 

I hope this helps. Regards,

 

Vikas

 

Highlighted
SRX Services Gateway

Re: Unable to find option to configure ADSL2+ on SRX110-va

‎09-18-2019 07:16 AM

Hi Dees,

 

Please refer the following KB article for configuring PPPoA - https://kb.juniper.net/InfoCenter/index?page=content&id=KB25400&cat=J_SERIES&actp=LIST



Thanks,
π00bm@$t€®.
Please, Mark My Solution Accepted if it Helped, Kudos are Appreciated too!!!
Feedback