Hi guys,
I'm trying to connect to Juniper NS5GT (Hardware Version: 1010, Firmware Version:6.2.0r2.0 Firewall+VPN) with Shrew VPN Client 2.1.7 (running on Win7 64bit) without success.
I used http://www.shrew.net/support/wiki/HowtoJuniperSsg to configure both sides.
Messages in shrew client window are
===
config loaded for site '222.61.123.22'
configuring client settings...
attached to key daemon ...
peer configured
iskamp proposal configured
esp proposal configured
client configured
local id configured
remote id configured
pre-shared key configured
bringing up tunnel ...
user authentication error
tunnel disabled
detached from key daemon ...
===
Error Messages on juniper are
===
2011-02-27 15:27:29 info IKE 62.143.130.124: XAuth login failed for gateway vpnclient_gateway, username thorsten, retry: 0, timeout: 1.
2011-02-27 15:27:29 info Rejected an IKE packet on ethernet3 from 62.143.130.124:4500 to 222.61.123.22:4500 with cookies e11944da1f039872 and b6cc949745492852 because A Phase 2 packet arrived while XAuth was still pending.
2011-02-27 15:27:29 info IKE 62.143.130.124 Phase 1: Completed Aggressive mode negotiations with a 28800-second lifetime.
2011-02-27 15:27:29 info IKE 62.143.130.124 Phase 1: Completed for user client.jersa.de.
2011-02-27 15:27:29 info IKE<62.143.130.124> Phase 1: IKE responder has detected NAT in front of the remote device.
2011-02-27 15:27:29 info IKE<62.143.130.124> Phase 1: IKE responder has detected NAT in front of the local device.
2011-02-27 15:27:29 info IKE 62.143.130.124 phase 1:The symmetric crypto key has been generated successfully.
2011-02-27 15:27:29 info IKE 62.143.130.124 Phase 1: Responder starts AGGRESSIVE mode negotiations.
===
The pw for user thorsten is correct, I already tried to connect with a wrong pw and got a different error message.
Shrew Configuration is
===
n:version:2
n:network-ike-port:500
n:network-mtu-size:1380
n:client-addr-auto:1
n:network-natt-port:4500
n:network-natt-rate:15
n:network-frag-size:540
n:network-dpd-enable:1
n:client-banner-enable:0
n:network-notify-enable:1
n:client-wins-used:0
n:client-wins-auto:1
n:client-dns-used:1
n:client-dns-auto:1
n:client-splitdns-used:0
n:client-splitdns-auto:0
n:phase1-dhgroup:2
n:phase1-life-secs:86400
n:phase1-life-kbytes:0
n:vendor-chkpt-enable:0
n:phase2-life-secs:3600
n:phase2-life-kbytes:0
n:policy-nailed:0
n:policy-list-auto:0
n:phase2-keylen:0
s:network-host:222.61.123.22
s:client-auto-mode:push
s:client-iface:direct
s:network-natt-mode:enable
s:network-frag-mode:enable
s:auth-method:mutual-psk-xauth
s:ident-client-type:fqdn
s:ident-server-type:fqdn
s:ident-client-data:client.jersa.de
s:ident-server-data:vpngw.jersa.de
b:auth-mutual-psk:dGVzdDJURVNU
s:phase1-exchange:aggressive
s:phase1-cipher:auto
s:phase1-hash:auto
s:phase2-transform:auto
s:phase2-hmac:auto
s:ipcomp-transform:disabled
n:phase2-pfsgroup:-1
s:policy-level:auto
s:policy-list-include:10.1.1.0 / 255.255.255.0
===
Configuration of juniper is
===
unset key protection enable
set clock ntp
set clock timezone 1
set clock dst recurring start-weekday 2 0 3 02:00 end-weekday 1 0 11 02:00
set vrouter trust-vr sharable
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
unset auto-route-export
exit
set service "Videoserver TCP 9999" protocol tcp src-port 0-65535 dst-port 9999-9999
set service "pcanywhere" protocol tcp src-port 0-65535 dst-port 5631-5631
set service "pcanywhere" + udp src-port 0-65535 dst-port 5632-5632
set service "POP3s" protocol tcp src-port 0-65535 dst-port 995-995
set service "SMTPs" protocol tcp src-port 0-65535 dst-port 465-465
set alg appleichat enable
unset alg appleichat re-assembly enable
unset alg p2p enable
set alg sctp enable
set auth-server "Local" id 0
set auth-server "Local" server-name "Local"
set auth default auth server "Local"
set auth radius accounting port 1646
set zone "Trust" vrouter "trust-vr"
set zone "Untrust" vrouter "untrust-vr"
set zone "DMZ" vrouter "trust-vr"
set zone "VLAN" vrouter "trust-vr"
set zone id 100 "vpn"
set zone "Untrust-Tun" vrouter "trust-vr"
set zone "Trust" tcp-rst
set zone "Untrust" block
unset zone "Untrust" tcp-rst
set zone "MGT" block
set zone "DMZ" tcp-rst
unset zone "V1-Trust" tcp-rst
unset zone "V1-Untrust" tcp-rst
unset zone "VLAN" tcp-rst
unset zone "vpn" tcp-rst
set zone "Untrust" screen tear-drop
set zone "Untrust" screen syn-flood
set zone "Untrust" screen ping-death
set zone "Untrust" screen ip-filter-src
set zone "Untrust" screen land
set zone "V1-Untrust" screen tear-drop
set zone "V1-Untrust" screen syn-flood
set zone "V1-Untrust" screen ping-death
set zone "V1-Untrust" screen ip-filter-src
set zone "V1-Untrust" screen land
set interface "ethernet1" zone "Trust"
set interface "ethernet2" zone "DMZ"
set interface "ethernet3" zone "Untrust"
set interface ethernet1 ip 10.1.1.1/24
set interface ethernet1 nat
set interface ethernet2 ip 10.99.99.1/24
set interface ethernet2 nat
set interface ethernet3 ip 222.61.123.22/30
set interface ethernet3 route
unset interface vlan1 ip
set interface ethernet1 proxy dns
unset interface vlan1 bypass-others-ipsec
unset interface vlan1 bypass-non-ip
set interface ethernet1 ip manageable
unset interface ethernet2 ip manageable
set interface ethernet3 ip manageable
unset interface ethernet1 manage telnet
unset interface ethernet1 manage snmp
set interface ethernet3 manage ssh
set interface ethernet3 manage ssl
set interface ethernet3 vip interface-ip 9999 "HTTP" 10.99.99.99
unset interface ethernet1 dhcp server config next-server-ip
unset interface ethernet1 dhcp server config updatable
set flow tcp-mss
unset flow no-tcp-seq-check
set flow tcp-syn-check
unset flow tcp-syn-bit-check
set flow reverse-route clear-text prefer
set flow reverse-route tunnel always
set console page 0
set hostname nsjs
set dbuf usb filesize 0
set pki authority default scep mode "auto"
set pki x509 default cert-path partial
set dns host dns3 0.0.0.0
set dns host name ns-5gt-205 10.1.1.1
set dns proxy
set dns proxy enable
set dns server-select domain * outgoing-interface ethernet3 primary-server 212.202.215.1 secondary-server 212.202.215.2 tertiary-server 194.8.194.60
set address "Trust" "10.1.1.0/24" 10.1.1.0 255.255.255.0
set address "DMZ" "10.255.255.0/24" 10.255.255.0 255.255.255.0
set address "DMZ" "10.99.99.0/24" 10.99.99.0 255.255.255.0
set ippool "vpnclient" 10.1.2.1 10.1.2.10
set user "thorsten" uid 2
set user "thorsten" type xauth
set user "thorsten" remote ippool "vpnclient"
set user "thorsten" password "***"
unset user "thorsten" type auth
set user "thorsten" "enable"
set user "vpnclient_ph1id" uid 1
set user "vpnclient_ph1id" ike-id fqdn "client.jersa.de" share-limit 2
set user "vpnclient_ph1id" type ike
set user "vpnclient_ph1id" "enable"
set user-group "vpnclient_group" id 1
set user-group "vpnclient_group" user "vpnclient_ph1id"
set crypto-policy
exit
set ike gateway "vpnclient_gateway" dialup "vpnclient_group" Aggr local-id "vpngw.jersa.de" outgoing-interface "ethernet3" preshare "***" proposal "pre-g2-3des-sha" "pre-g2-3des-md5" "pre-g2-aes128-sha" "pre-g2-aes128-md5"
set ike gateway "vpnclient_gateway" dpd-liveness interval 30
unset ike gateway "vpnclient_gateway" nat-traversal udp-checksum
set ike gateway "vpnclient_gateway" nat-traversal keepalive-frequency 20
set ike gateway "vpnclient_gateway" xauth server "Local"
unset ike gateway "vpnclient_gateway" xauth do-edipi-auth
set ike respond-bad-spi 1
set ike ikev2 ike-sa-soft-lifetime 60
unset ike ikeid-enumeration
unset ike dos-protection
unset ipsec access-session enable
set ipsec access-session maximum 5000
set ipsec access-session upper-threshold 0
set ipsec access-session lower-threshold 0
set ipsec access-session dead-p2-sa-timeout 0
unset ipsec access-session log-error
unset ipsec access-session info-exch-connected
unset ipsec access-session use-error-log
set xauth default ippool "vpnclient"
set xauth default dns1 10.1.1.1
set vpn "vpnclient_tunnel" gateway "vpnclient_gateway" replay tunnel idletime 0 proposal "nopfs-esp-3des-sha" "nopfs-esp-3des-md5" "nopfs-esp-aes128-sha" "nopfs-esp-aes128-md5"
set vpn "vpnclient_tunnel" monitor
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
exit
set url protocol websense
exit
set policy id 11 from "Trust" to "Untrust" "Any" "Any" "ANY" permit log
set policy id 11 disable
set policy id 11
exit
set policy id 1 from "Trust" to "Untrust" "10.1.1.0/24" "Any" "DNS" permit log
set policy id 1
set service "FTP"
set service "HTTP"
set service "HTTPS"
set service "NTP"
set service "pcanywhere"
set service "PING"
set service "POP3"
set service "POP3s"
set service "SMTP"
set service "SMTPs"
set service "TRACEROUTE"
set service "Videoserver TCP 9999"
exit
set policy id 4 from "Trust" to "Untrust" "Any" "Any" "UDP-ANY" deny log
set policy id 4
exit
set policy id 12 from "Untrust" to "DMZ" "Any" "Any" "ANY" permit log
set policy id 12 disable
set policy id 12
exit
set policy id 2 from "Untrust" to "DMZ" "Any" "VIP(ethernet3)" "HTTP" permit log
set policy id 2
set service "HTTPS"
set service "Videoserver TCP 9999"
exit
set policy id 3 from "Trust" to "Untrust" "Any" "Any" "ANY" deny log
set policy id 3
exit
set policy id 5 from "Untrust" to "DMZ" "Any" "Any" "ANY" deny log
set policy id 5
exit
set policy id 6 from "Trust" to "DMZ" "10.1.1.0/24" "10.99.99.0/24" "HTTP" permit log
set policy id 6
set service "HTTPS"
set service "PING"
exit
set policy id 7 from "Trust" to "DMZ" "Any" "Any" "ANY" deny log
set policy id 7
exit
set policy id 16 from "Untrust" to "Trust" "Any" "Any" "ANY" permit log
set policy id 16 disable
set policy id 16
exit
set policy id 15 name "vpnclient_inbound" from "Untrust" to "Trust" "Dial-Up VPN" "10.1.1.0/24" "ANY" tunnel vpn "vpnclient_tunnel" id 0x2 log
set policy id 15
exit
set policy id 8 from "Untrust" to "Trust" "Any" "Any" "ANY" deny log
set policy id 8
exit
set policy id 13 from "DMZ" to "Trust" "Any" "Any" "ANY" permit log
set policy id 13 disable
set policy id 13
exit
set policy id 9 from "DMZ" to "Trust" "Any" "Any" "ANY" deny log
set policy id 9
exit
set policy id 14 from "DMZ" to "Untrust" "Any" "Any" "ANY" permit log
set policy id 14 disable
set policy id 14
exit
set policy id 10 from "DMZ" to "Untrust" "Any" "Any" "ANY" deny log
set policy id 10
exit
set log cli enable
set nsmgmt bulkcli reboot-timeout 60
set ssh version v2
set ssh enable
set config lock timeout 5
unset license-key auto-update
set ssl port 23143
set ntp server "192.53.103.103"
set ntp server backup1 "192.53.103.104"
set ntp server backup2 "192.53.103.108"
set ntp interval 1440
set modem speed 115200
set modem retry 3
set modem interval 10
set modem idle-time 10
set snmp port listen 161
set snmp port trap 162
set vrouter "untrust-vr"
set route 0.0.0.0/0 interface ethernet3 gateway *** permanent
set route 10.1.1.0/24 vrouter "trust-vr" preference 20 metric 1
set route 10.99.99.0/24 vrouter "trust-vr" preference 20 metric 1
exit
set vrouter "trust-vr"
unset add-default-route
set route 0.0.0.0/0 vrouter "untrust-vr" preference 20 metric 1
exit
set vrouter "untrust-vr"
exit
set vrouter "trust-vr"
exit
===
Shrew Debug log is attached. I think "user thorsten authentication failed" is the relevant message
Juniper Debug log (debug ike detail) is also attached. I think “xauth login FAILED. gw <vpnclient_gateway>, username <thorsten>, retry: 0, timeout: 1” is the relevant message.
Timestamps don't match because I took the debugs at different points of time.
Does anybody have an idea what's going wrong?
Many thanks in advance
Thorsten
#NS5GT#shrew