vMX

Issue:

======

IPsec VPN b/w Juniper vMX and Vyatta 5400 not working .

 

Topology:

========

 

192.168.100.1/24------Vyatta---------------Cloud--------------AWS ------Juniper vMX---10.0.20.0/24

 

Corcerns or Problems:

==================

1.  since the deployment is in AWS VPC the Public or Revenue interface is not in default Routing instance so both Public ge-0/0/0 and ge0/0/1 are in Routing instance named DATAPLANE-VMX-VPN-WANCLOUDS.And if my understanding is correct both si-0/0/0.1 and si-0/0/0.1 should be part of routing instance DATAPLANE-VMX-VPN-WANCLOUDS but on configuring getting this error.

 

root@Juniper-vMX-Wanclouds# set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.1 

 

[edit]

root@Juniper-vMX-Wanclouds# set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2    

 

[edit]

root@Juniper-vMX-Wanclouds# commit check 

[edit services service-set IPSEC-SITE-TO-SITE]

  'ipsec-vpn-options'

    The service interface si-0/0/0.2 must be configured under default routing-instance

 

2. How to enable NAT Traversal for IPsec vpn on vMX as the VMx is deployed behind Internet Gateway 1:1 Nat.But as per my undersatnding its enable by default.

 

 

 

Configuration:

 

Vyatta5400:

----------------

 

#vmx
#NAT
#vyatta
#routing-instance
#IPSec

Hi,

Your config doesn’t seem to be correct.
You have both inside and outside interface in same routing-instance DATAPLANE-VMX-VPN-WANCLOUDS.

Your local gateway and outside service interface should be either in global routing-instance or in another routing-instance.

I will correct the config and share if needed

Here’s the config for your reference.

Topology:

R1----------------------------R2

R1 config:


[edit]
root@R1_re# run show services ipsec-vpn ike sa
Remote Address State Initiator cookie Responder cookie Exchange type
10.1.12.2 Matured 846c851af53cecfd 221279f553a29262 Main

[edit]
root@R1_re#

[edit]
root@R1_re# run show services ipsec-vpn ipsec sa
Service set: test, IKE Routing-instance: outside

Rule: test-vpn, Term: 1, Tunnel index: 1
Local gateway: 10.1.12.1, Remote gateway: 10.1.12.2
IPSec inside interface: si-0/0/0.1, Tunnel MTU: 1500
UDP encapsulate: Disabled, UDP Destination port: 0
NATT Detection: Not Detected, NATT keepalive interval: 0
Direction SPI AUX-SPI Mode Type Protocol
inbound 4044436681 0 tunnel dynamic ESP
outbound 1708770906 0 tunnel dynamic ESP

[edit]
root@R1_re#

[edit]
root@R1_re# show services | display set
set services rpm probe A test PING-A-1 probe-type icmp-ping
set services rpm probe A test PING-A-1 target address 10.1.12.2
set services rpm probe A test PING-A-1 test-interval 3
set services rpm probe A test PING-A-1 thresholds successive-loss 3
set services service-set test next-hop-service inside-service-interface si-0/0/0.1
set services service-set test next-hop-service outside-service-interface si-0/0/0.2
set services service-set test ipsec-vpn-options local-gateway 10.1.12.1
set services service-set test ipsec-vpn-options local-gateway routing-instance outside
set services service-set test ipsec-vpn-rules test-vpn
set services ipsec-vpn rule test-vpn term 1 from source-address 192.168.0.0/24
set services ipsec-vpn rule test-vpn term 1 from destination-address 172.16.0.0/24
set services ipsec-vpn rule test-vpn term 1 then remote-gateway 10.1.12.2
set services ipsec-vpn rule test-vpn term 1 then dynamic ike-policy ike-policy
set services ipsec-vpn rule test-vpn term 1 then dynamic ipsec-policy ipsec-policy
set services ipsec-vpn rule test-vpn match-direction input
set services ipsec-vpn ipsec proposal ipsec-proposal authentication-algorithm hmac-md5-96
set services ipsec-vpn ipsec proposal ipsec-proposal encryption-algorithm 3des-cbc
set services ipsec-vpn ipsec policy ipsec-policy proposals ipsec-proposal
set services ipsec-vpn ike proposal ike-proposal authentication-method pre-shared-keys
set services ipsec-vpn ike proposal ike-proposal dh-group group5
set services ipsec-vpn ike proposal ike-proposal encryption-algorithm 3des-cbc
set services ipsec-vpn ike proposal ike-proposal lifetime-seconds 500
set services ipsec-vpn ike policy ike-policy proposals ike-proposal
set services ipsec-vpn ike policy ike-policy pre-shared-key ascii-text "$9$Tz/Cp0BESru07-bs4o/CAtIEM8X"
set services ipsec-vpn establish-tunnels immediately

[edit]
root@R1_re#

root@R1_re# show routing-instances | display set
set routing-instances inside instance-type virtual-router
set routing-instances inside interface si-0/0/0.1
set routing-instances inside interface ge-0/0/2.0
set routing-instances inside routing-options static route 172.16.0.0/24 next-hop si-0/0/0.1
set routing-instances inside routing-options static route 192.168.0.0/24 next-hop 10.1.14.4
set routing-instances outside instance-type virtual-router
set routing-instances outside interface si-0/0/0.2
set routing-instances outside interface ge-0/0/1.0
set routing-instances outside routing-options static route 172.16.0.0/24 next-hop 10.1.12.2

[edit]
[edit]
root@R1_re# show interfaces
si-0/0/0 {
unit 1 {
family inet;
service-domain inside;
}
unit 2 {
family inet;
service-domain outside;
}
}
ge-0/0/1 {
unit 0 {
family inet {
address 10.1.12.1/24;
}
}
}
ge-0/0/2 {
unit 0 {
family inet {
address 10.1.14.1/24;
}
}
}


R2: Config



[edit]
root@R2_re# show services | display set
set services service-set test next-hop-service inside-service-interface si-0/0/0.1
set services service-set test next-hop-service outside-service-interface si-0/0/0.2
set services service-set test ipsec-vpn-options local-gateway 10.1.12.2
set services service-set test ipsec-vpn-options local-gateway routing-instance outside
set services service-set test ipsec-vpn-rules test-vpn
set services ipsec-vpn rule test-vpn term 1 from source-address 172.16.0.0/24
set services ipsec-vpn rule test-vpn term 1 from destination-address 192.168.0.0/24
set services ipsec-vpn rule test-vpn term 1 then remote-gateway 10.1.12.1
set services ipsec-vpn rule test-vpn term 1 then dynamic ike-policy ike-policy
set services ipsec-vpn rule test-vpn term 1 then dynamic ipsec-policy ipsec-policy
set services ipsec-vpn rule test-vpn match-direction input
set services ipsec-vpn ipsec proposal ipsec-proposal authentication-algorithm hmac-md5-96
set services ipsec-vpn ipsec proposal ipsec-proposal encryption-algorithm 3des-cbc
set services ipsec-vpn ipsec policy ipsec-policy proposals ipsec-proposal
set services ipsec-vpn ike proposal ike-proposal authentication-method pre-shared-keys
set services ipsec-vpn ike proposal ike-proposal dh-group group5
set services ipsec-vpn ike proposal ike-proposal encryption-algorithm 3des-cbc
set services ipsec-vpn ike proposal ike-proposal lifetime-seconds 500
set services ipsec-vpn ike policy ike-policy proposals ike-proposal
set services ipsec-vpn ike policy ike-policy pre-shared-key ascii-text "$9$Tz/Cp0BESru07-bs4o/CAtIEM8X"
set services ipsec-vpn establish-tunnels immediately

[edit]
root@R2_re#

[edit]
root@R2_re# show routing-instances | display set
set routing-instances inside instance-type virtual-router
set routing-instances inside interface si-0/0/0.1
set routing-instances inside interface ge-0/0/2.0
set routing-instances inside routing-options static route 192.168.0.0/24 next-hop si-0/0/0.1
set routing-instances inside routing-options static route 172.16.0.0/24 next-hop 10.1.23.3
set routing-instances outside instance-type virtual-router
set routing-instances outside interface si-0/0/0.2
set routing-instances outside interface ge-0/0/1.0
set routing-instances outside routing-options static route 192.168.0.0/24 next-hop 10.1.12.1

[edit]
root@R2_re#
[edit]
root@R2_re# show interfaces
si-0/0/0 {
unit 1 {
family inet;
service-domain inside;
}
unit 2 {
family inet;
service-domain outside;
}
}
ge-0/0/1 {
unit 0 {
family inet {
address 10.1.12.2/24;
}
}
}
ge-0/0/2 {
unit 0 {
family inet {
address 10.1.23.2/24;
}
}
}

[edit]
root@R2_re# run show services ipsec-vpn ike sa
Remote Address State Initiator cookie Responder cookie Exchange type
10.1.12.1 Matured 846c851af53cecfd 221279f553a29262 Main

[edit]
root@R2_re# run show services ipsec-vpn ipsec sa
Service set: test, IKE Routing-instance: outside

Rule: test-vpn, Term: 1, Tunnel index: 1
Local gateway: 10.1.12.2, Remote gateway: 10.1.12.1
IPSec inside interface: si-0/0/0.1, Tunnel MTU: 1500
UDP encapsulate: Disabled, UDP Destination port: 0
NATT Detection: Not Detected, NATT keepalive interval: 0
Direction SPI AUX-SPI Mode Type Protocol
inbound 1708770906 0 tunnel dynamic ESP
outbound 4044436681 0 tunnel dynamic ESP

[edit]
root@R2_re#



HTH

You can also do it without “outside routing-instance” as well. just keep your local gateway and outside service interface in global table and remove the routing-instance statement from below command.

set services service-set test ipsec-vpn-options local-gateway 155.1.12.2
set services service-set test ipsec-vpn-options local-gateway routing-instance outside

Thanks a lot for looking inot it and providing the working configs .Will try to move the inside interface to global routing table and update you .The reason i am using the Routing Instance as i have one public elastic ip and if i attach to fxp management interface then i cannot create ipsec vpn .The only possible option is to move the gig interface from default routing instance .

I believe, it was the outside (WAN) interface which is used as a local-gateway for the IPsec-tunnel.

Thanks again but i have some doubts and would like to clear before changing the configuration attaching the Topology just to give some background and then would like to understand if i am missing something or my approach is not correct.

 

Goal :

======

Device connected behind Vyatta 5400 can access the File and DB servers connected to VMX on ge-0/0/1 and ge-0/0/2.

 

Corncerns:

=========

1.This deployment is in AWS VPC and using Elastic IP which is public and if i attach the eleastic IP to FXP0 then i cannot create IPSec as its Mgmt interface and if i attach this Elastic IP to Revenue or Ge-0/0/0 interface then i cannot access the vMX or device as its in same Routing table that is global routing instance.So i decieded to create a Routing instance "DATAPLANE-VMX-VPN-WANCLOUDS" and move both my ge-0/0/0 interface which is basically public interface and ge-0/0/1 and ge-0/0/2 interafce where the internal File and DB server is connected and i am able to ping from ge-0/0/0 public to vyatta 5400 wan interface.

 

2.Now i configured the IPSec vpn b/w ge-0/0/0 of vMX and Vyatta5400 device but for that i need to create si 

si-0/0/0.1 inside-interface , si-0/0/0.2 outside interface and here i am confused meaning these interface are some how tied to ge-0/0/0 and ge-0/0/1 ? or si-0/0/0.2 outside interface and ge-0/0/0 wan public interface will remain in Routing instance "DATAPLANE-VMX-VPN-WANCLOUDS" and i have to move the si-0/0/0.1 inside-interface and ge-0/0/1 and ge-0/0/2 interfaces ( where internal servers are connected)  should be moved to global or default Routing-instance or only si-0/0/0.1 inside-interface should be moved from this "DATAPLANE-VMX-VPN-WANCLOUDS" routing instance.

 

Regards

Syed.

 

The reason i brought the earlier discussion that i have tested the similar setup with vSRX Firewall IPsec VPN and all the interfaces was part of same Routing-Instance DATAPLANE-VPN-WANCLOUDS including st virtual interface. The only difference was zones Trust and Untrust . Wan interface ge-0/0/0 and st0.0 were part of Untrust Zone and ge-0/0/1 Trust zone.

 

 

set routing-instances DATAPLANE-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VPN-WANCLOUDS interface ge-0/0/1.0

set routing-instances DATAPLANE-VPN-WANCLOUDS interface st0.0

Ok.. So you can configure IPsec VPN in 3 ways in this case.

First:

Put Outside interface ( ge-0/0/0 and si-0/0/0.2) in one routing-instance and Inside interface (ge-0/0/1, ge-0/0/2 & si-0/0/0.1 ) in once routing instance.
This config I already shared.


Second:


Keep your (outside interface) ge-0/0/0 and si-0/0/0.2 in DATAPLANE-VMX-VPN-WANCLOUDS and Inside interface (ge-0/0/1, ge-0/0/2 & si-0/0/0.1) in global table.

You need to add a static route in the global table for the traffic destined to Device connected behind Vyatta as below.

Set routing-option static route <SUBNET> next-hop si-0/0/0.1

Also, make sure you have a route for the destination in DATAPLANE-VMX-VPN-WANCLOUDS routing-instance pointing towards Vyatta.


Topology:
10.1.12.0/24
R1-(.1)--------------------------------------------------------------------(.2)-R2


root@R1_re# show services service-set test
next-hop-service {
inside-service-interface si-0/0/0.1;
outside-service-interface si-0/0/0.2;
}
ipsec-vpn-options {
local-gateway 10.1.12.1 routing-instance DATAPLANE-VMX-VPN-WANCLOUDS;
}
ipsec-vpn-rules test-vpn;

[edit]
root@R1_re#


root@R1_re# show routing-options
static {
route 172.16.0.0/24 next-hop si-0/0/0.1;
route 192.168.0.0/24 next-hop 10.1.14.4;
}
router-id 11.11.11.11;
autonomous-system 100;


[edit]
root@R1_re# show routing-instances DATAPLANE-VMX-VPN-WANCLOUDS
instance-type virtual-router;
interface si-0/0/0.2;
interface ge-0/0/1.0;
routing-options {
static {
route 172.16.0.0/24 next-hop 10.1.12.2;
}
}

[edit]
root@R1_re#


ipsec-vpn {
rule test-vpn {
term 1 {
from {
source-address {
192.168.0.0/24;
}
destination-address {
172.16.0.0/24;
}
}
then {
remote-gateway 10.1.12.2;
dynamic {
ike-policy ike-policy;
ipsec-policy ipsec-policy;
}
}
}
match-direction input;
}


Third Option:


Keep all the interface in DATAPLANE-VMX-VPN-WANCLOUDS as your original configuration.

And make below changes.

Add routing-instance knob with local-gateway as below. (this was missing in your config)

ipsec-vpn-options {
local-gateway 10.1.12.1 routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

Make sure you have all the routing correctly in place so that traffic destined to subnet (behind Vaytta) goes to si-0/0/0.1 interface first for the IPsec encapsulation and then go gout via ge-0/0/0 as per your topology.

I have to put a specific route for the destination subnet to make it work.

[edit]
root@R1_re# show routing-instances DATAPLANE-VMX-VPN-WANCLOUDS
instance-type virtual-router;
interface si-0/0/0.1;
interface si-0/0/0.2;
interface ge-0/0/1.0;
interface ge-0/0/2.0;
routing-options {
static {
route 172.16.0.0/24 next-hop [ 155.1.12.2 si-0/0/0.1 ];
route 192.168.0.0/24 next-hop 155.1.14.4;
}
}

[edit]
root@R1_re# set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 172.16.0.100/32 next-hop si-0/0/0.1

[edit]
root@R1_re# commit
commit complete

Let me know if you still have any question.

HTH.</SUBNET>

Hi,

 

Did it work for you?

 

 

Hi Kingsman,

I have tried with the sugested confguration but still its not working.

 

1. Routing-Instance DATAPLANE-VMX-VPN-WANCLOUDS

    i.  ge-0/0/0 and si-0/0/0.2 

 

2. Global Routing-Instance:

    i. ge-0/0/1 and si-0/0/0.2

    ii. set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1 ( where 192.168.100.1 is connected to Vyatta)

 

 

vMX:

====

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.115.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn establish-tunnels immediately

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

 set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.115.92

root@Juniper-vMX-Wanclouds> show configuration services service-set IPSEC-SITE-TO-SITE    

next-hop-service {

    inside-service-interface si-0/0/0.1;

    outside-service-interface si-0/0/0.2;

}

ipsec-vpn-options {

    local-gateway 10.0.10.12 routing-instance DATAPLANE-VMX-VPN-WANCLOUDS;

}

ipsec-vpn-rules IPSec-VYATTA;

 

root@Juniper-vMX-Wanclouds> 

 

 

root@Juniper-vMX-Wanclouds> 

 

root@Juniper-vMX-Wanclouds> monitor traffic interface ge-0/0/0 matching udp               

verbose output suppressed, use <detail> or <extensive> for full protocol decode

Address resolution is ON. Use <no-resolve> to avoid any reverse lookup delay.

Address resolution timeout is 4s.

Listening on ge-0/0/0, capture size 96 bytes

 

Reverse lookup for 10.0.10.12 failed (check DNS reachability).

Other reverse lookup failures will not be reported.

Use <no-resolve> to avoid reverse lookups on IP addresses.

 

01:34:30.002214  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:34:30.008571 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:34:52.718981  In IP 107.173.40.203.5063 > 10.0.10.12.sip: SIP, length: 416

01:35:10.225491  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:35:10.231659 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:35:50.448662  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:35:50.454043 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:36:29.670526  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:36:29.676629 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:37:09.893797  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:37:09.899046 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:37:50.114708  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:37:50.121600 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

01:38:30.344314  In IP 168.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

01:38:30.350602 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 168.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

 

Vyatta:

 

vyatta@gw-melbourne1-02-06-2016:~$ show configuration commands | grep vpn
set vpn ipsec esp-group ESP-1H compression 'disable'
set vpn ipsec esp-group ESP-1H lifetime '27000'
set vpn ipsec esp-group ESP-1H mode 'tunnel'
set vpn ipsec esp-group ESP-1H pfs 'dh-group5'
set vpn ipsec esp-group ESP-1H proposal 1 encryption '3des'
set vpn ipsec esp-group ESP-1H proposal 1 hash 'md5'
set vpn ipsec ike-group IKE-1H lifetime '28800'
set vpn ipsec ike-group IKE-1H proposal 1 dh-group '5'
set vpn ipsec ike-group IKE-1H proposal 1 encryption '3des'
set vpn ipsec ipsec-interfaces interface 'bond1'
set vpn ipsec nat-traversal 'enable'
set vpn ipsec site-to-site peer 35.163.189.77 authentication id '108.1.115.92'
set vpn ipsec site-to-site peer 35.163.189.77 authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer 35.163.189.77 authentication pre-shared-secret 'cisco1000'
set vpn ipsec site-to-site peer 35.163.189.77 authentication remote-id '35.163.189.77'
set vpn ipsec site-to-site peer 35.163.189.77 connection-type 'initiate'
set vpn ipsec site-to-site peer 35.163.189.77 default-esp-group 'ESP-1H'
set vpn ipsec site-to-site peer 35.163.189.77 ike-group 'IKE-1H'
set vpn ipsec site-to-site peer 35.163.189.77 local-address '108.1.115.92'
set vpn ipsec site-to-site peer 35.163.189.77 tunnel 0 allow-nat-networks 'disable'
set vpn ipsec site-to-site peer 35.163.189.77 tunnel 0 allow-public-networks 'disable'
set vpn ipsec site-to-site peer 35.163.189.77 tunnel 0 local prefix '192.168.100.0/24'
set vpn ipsec site-to-site peer 35.163.189.77 tunnel 0 remote prefix '10.0.20.0/24'
vyatta@gw-melbourne1-02-06-2016:~$

 

 

The config looks good. Do you have any nat device between the 2 peers?

 

 

Vyatta is Public Device in Softlayer Cloud and Juniper vMX is on AWS clouds which is basically 1:1 Nat as its behind Nat-Gateway.And i believe NAT traversal is by default on Juniper vMX.

 

Regards

Syed

Can you disable the Natt on mx and check?

Get Outlook for Android<>

What’s the command to disable Nat on Vmx but don’t u think it will cause
issues later as this device is behind Nat.

Disable NAT Transversal

set services ipsec-vpn disable-natt

Thanks again i will try and share the results

 

Hi,

NATT is officially is supported from 17.4 on MX platform. I need to check it’s the same case with vMX as well but for now, can you try disabling NATT and check if it works?

You can refer to below link.

https://www.juniper.net/documentation/en_US/junos/topics/task/configuration/services-ipsec-nat-t-disabling.html

HTH

Thanks Again and will share the output.

I have disabled the NAT Traversal on Juniper vMX but still the same issue.

 

root@Juniper-vMX-Wanclouds> show configuration | display set | grep nat 

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn disable-natt

 

 

 

root@Juniper-vMX-Wanclouds> ping 108.1.115.92 routing-instance DATAPLANE-VMX-VPN-WANCLOUDS interface ?

Possible completions:

  <interface>          Source interface (multicast, all-ones, unrouted packets)

root@Juniper-vMX-Wanclouds> ping 108.1.115.92 routing-instance DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0 

PING 108.1.115.92 (108.1.115.92): 56 data bytes

64 bytes from 108.1.115.92: icmp_seq=0 ttl=40 time=193.308 ms

64 bytes from 108.1.115.92: icmp_seq=1 ttl=40 time=192.126 ms

64 bytes from 108.1.115.92: icmp_seq=2 ttl=40 time=189.996 ms

64 bytes from 108.1.115.92: icmp_seq=3 ttl=40 time=189.118 ms

64 bytes from 108.1.115.92: icmp_seq=4 ttl=40 time=189.470 ms

^C

--- 108.1.115.92 ping statistics ---

6 packets transmitted, 5 packets received, 16% packet loss

round-trip min/avg/max/stddev = 189.118/190.804/193.308/1.631 ms

 

root@Juniper-vMX-Wanclouds> show configuration | display set                                                       

set version 17.2R1.13

 

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.115.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn establish-tunnels immediately

set services ipsec-vpn disable-natt

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.115.92

 

 

 

root@Juniper-vMX-Wanclouds> 

 

 

root@Juniper-vMX-Wanclouds> monitor traffic interface ge-0/0/0 matching udp 

verbose output suppressed, use <detail> or <extensive> for full protocol decode

Address resolution is ON. Use <no-resolve> to avoid any reverse lookup delay.

Address resolution timeout is 4s.

Listening on ge-0/0/0, capture size 96 bytes

 

Reverse lookup for 10.0.10.12 failed (check DNS reachability).

Other reverse lookup failures will not be reported.

Use <no-resolve> to avoid reverse lookups on IP addresses.

 

22:37:27.258324  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:37:27.266412 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:38:06.285971  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:38:06.291761 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:38:46.316629  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:38:46.322870 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:39:27.074786  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:39:27.081587 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:40:06.369408  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:40:06.376011 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:40:16.572681  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:40:16.577964 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:40:36.395870  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:40:36.402259 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:41:16.426245  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:41:16.435971 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

22:41:56.454951  In IP 108.1.115.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

22:41:56.462379 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.115.92.isakmp: isakmp: phase 2/others R inf: [|n]

^C

98 packets received by filter

0 packets dropped by kernel

 

 

 

set vpn ipsec esp-group ESP-1H compression 'disable'

set vpn ipsec esp-group ESP-1H lifetime '27000'

set vpn ipsec esp-group ESP-1H mode 'tunnel'

set vpn ipsec esp-group ESP-1H pfs 'dh-group5'

set vpn ipsec esp-group ESP-1H proposal 1 encryption '3des'

set vpn ipsec esp-group ESP-1H proposal 1 hash 'md5'

set vpn ipsec ike-group IKE-1H lifetime '28800'

set vpn ipsec ike-group IKE-1H proposal 1 dh-group '5'

set vpn ipsec ike-group IKE-1H proposal 1 encryption '3des'

set vpn ipsec ipsec-interfaces interface 'bond1'

set vpn ipsec nat-traversal 'enable'

set vpn ipsec site-to-site peer 35.162.145.118 authentication id '108.1.115.92'

set vpn ipsec site-to-site peer 35.162.145.118 authentication mode 'pre-shared-secret'

set vpn ipsec site-to-site peer 35.162.145.118 authentication pre-shared-secret 'cisco1000'

set vpn ipsec site-to-site peer 35.162.145.118 authentication remote-id '35.162.145.118'

set vpn ipsec site-to-site peer 35.162.145.118 connection-type 'initiate'

set vpn ipsec site-to-site peer 35.162.145.118 default-esp-group 'ESP-1H'

set vpn ipsec site-to-site peer 35.162.145.118 ike-group 'IKE-1H'

set vpn ipsec site-to-site peer 35.162.145.118 local-address '108.1.115.92'

set vpn ipsec site-to-site peer 35.162.145.118 tunnel 0 allow-nat-networks 'disable'

set vpn ipsec site-to-site peer 35.162.145.118 tunnel 0 allow-public-networks 'disable'

set vpn ipsec site-to-site peer 35.162.145.118 tunnel 0 local prefix '192.168.100.0/24'

set vpn ipsec site-to-site peer 35.162.145.118 tunnel 0 remote prefix '10.0.20.0/24'

 

 

vyatta@gw-melbourne1-02-06-2016:~$ show vpn ike sa

Peer ID / IP                            Local ID / IP               

------------                            -------------

35.162.145.118                          108.1.115.92                           

 

    State  Encrypt  Hash  D-H Grp  NAT-T  A-Time  L-Time

    -----  -------  ----  -------  -----  ------  ------

    init   n/a      n/a   n/a      no     0       28800  

 

 

vyatta@gw-melbourne1-02-06-2016:~$ 

vyatta@gw-melbourne1-02-06-2016:~$ 

vyatta@gw-melbourne1-02-06-2016:~$ show vpn ipsec sa

Peer ID / IP                            Local ID / IP               

------------                            -------------

35.162.145.118                          108.1.115.92                           

 

    Tunnel  State  Bytes Out/In   Encrypt  Hash  NAT-T  A-Time  L-Time  Proto

    ------  -----  -------------  -------  ----  -----  ------  ------  -----

    0       down   n/a            n/a      n/a   no     0       27000   all

 

 

Regards

syed

Can you enable ipsec traceoption and attached the tracelog file here ?

https://www.juniper.net/documentation/en_US/junos/topics/reference/configuration-statement/traceoptions-edit-services-ipsec-vpn.html

Use level all and flag all while enabling the trace options.

I am attaching the ouput of log file.

Hi I see this in the logs.

Feb 7 00:22:33 [10.0.10.12 <-> 168.1.114.92] Instance: IPSEC-SITE-TO-SITE is down as service interface: si-0/0/0.2 is not up, Lookup failed.

Do you have tunnel-services enabled on the FPC? I don’t see tunnel-service configured in your configuration.

 

Hi ,

  Not sure how to enable tunnel services on FPC , checked some of the output to make sure if fpc status is ok .Can u share the command to enable tunnel services on FPC.

 

root@Juniper-vMX-Wanclouds> show chassis hardware detail     

Hardware inventory:

Item             Version  Part number  Serial number     Description

Chassis                                VM5A5406B749      VMX

Midplane        

Routing Engine 0                                         RE-VMX

  vtbd0     0 MB                                         Hard Disk

CB 0                                                     VMX SCB

CB 1                                                     VMX SCB

FPC 0                                                    Virtual FPC

  CPU            Rev. 1.0 RIOT         BUILTIN          

  MIC 0                                                  Virtual

    PIC 0                 BUILTIN      BUILTIN           Virtual

 

root@Juniper-vMX-Wanclouds> show chassis fpc pic-status      

Slot 0   Online       Virtual FPC                                   

  PIC 0  Online       Virtual

 

 

 

 

root@Juniper-vMX-Wanclouds> show chassis network-services 

Network Services Mode: IP

 

root@Juniper-vMX-Wanclouds> 

 

Regards

Syed

 

Set chassis fpc x pic x tunnel-services bandwidth 1/10g

Here x is the pic and pfc no.

Do you see your sister interface up on your box?

Can you paste the output of "show interface terse | match si"

Also make sure you are using the correct si interface.

Get Outlook for Android<>

Here is the output and i enabled tunnel services on Tunnel.

 

root@Juniper-vMX-Wanclouds> show interfaces terse | match si    -->Before enabling tunnel services on tunnel

esi                     up    up

lsi                     up    up

 

root@Juniper-vMX-Wanclouds> show chassis hardware 

Hardware inventory:

Item             Version  Part number  Serial number     Description

Chassis                                VM5A5406B749      VMX

Midplane        

Routing Engine 0                                         RE-VMX

CB 0                                                     VMX SCB

CB 1                                                     VMX SCB

FPC 0                                                    Virtual FPC

  CPU            Rev. 1.0 RIOT         BUILTIN          

  MIC 0                                                  Virtual

    PIC 0                 BUILTIN      BUILTIN           Virtual

 

root@Juniper-vMX-Wanclouds> set ch

                                  ^

syntax error.

root@Juniper-vMX-Wanclouds> configure 

Entering configuration mode

 

[edit]

root@Juniper-vMX-Wanclouds# set chassis fpc 0 pic 0 tunnel-services bandwidth ?

Possible completions:

  <bandwidth>          Bandwidth reserved for tunnel service

  100g                 100 gigabits per second

  10g                  10 gigabits per second

  1g                   1 gigabit per second

  200g                 200 gigabits per second

  20g                  20 gigabits per second

  300g                 300 gigabits per second

  30g                  30 gigabits per second

  400g                 400 gigabits per second

  40g                  40 gigabits per second

  50g                  50 gigabits per second

  60g                  60 gigabits per second

  70g                  70 gigabits per second

  80g                  80 gigabits per second

  90g                  90 gigabits per second

[edit]

 

root@Juniper-vMX-Wanclouds# set chassis fpc 0 pic 0 tunnel-services bandwidth 1g  

 

[edit]

root@Juniper-vMX-Wanclouds# commit 

commit complete

 

[edit]

root@Juniper-vMX-Wanclouds# 

 

Is it working now? You didn’t see si interface in the output (before enabling tunneling)

It should work now.

Still its not working i have tried all options , including the output from device and debug from vmx in attachment.Still complaining in debug the si interface down but interface output saying its up i think there is some issue vMX.

 

root@Juniper-vMX-Wanclouds> show interfaces terse | match si 

esi                     up    up

lsi                     up    up

 

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ikev2_fb_isakmp_select_sa: Taking reference to fallback negotiation 8d16400 (now 2 references)

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ssh_set_thread_debug_info: ikev2_fb_isakmp_select_sa: set thread debug info - local 0xc0a000a remote 0x5c7201a8neg 0x8d16400 neg->ike_sa 0x8cad200 ike_sa 0x0

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ike_state_step: Input function[1] = ike_st_i_sa_proposal asked retry later

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ike_process_packet: No output packet, returning

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ikev2_fb_st_select_ike_sa: FB; Calling v2 policy function select_ike_sa

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] In kmd_pm_spd_select_ike_sa: Enter SA 8cad200 ED 8e25028

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] Looking up IKE gateway for server: 10.0.10.12 and routing instance id: 8

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] instance: IPSEC-SITE-TO-SITE found for server: 10.0.10.12 in routing instance id: 8

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] Instance: IPSEC-SITE-TO-SITE is down as service interface: si-0/0/0.2 is not up, Lookup failed.

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] No instance available to serve this request

Mar  3 01:05:55 [10.0.10.12 <-> 108.1.114.92] ikev2_fb_spd_select_sa_cb: IKEv2 SA select failed with error Invalid argument (neg 8d16400)

 

root@Juniper-vMX-Wanclouds> show configuration | display set 

set version 17.2R1.13

set groups global system host-name Juniper-vMX-Wanclouds

set groups global system login user jnpr uid 2000

set groups global system login user jnpr class super-user

set groups global system login user jnpr authentication ssh-rsa "ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCxHi+V3riqQj4QPAksAAs2ATrbJlUCyPzWEZtBtQS5pdjm6xa9xXVYcyxwEu3CmmyMDAf4xt6thJvvNZbFZRoo9k0W4cTn4BiqeBBhjfaPeowkErpNugCyJZMkmId/sdLuZ/TrcGV0ZFI8l8ojAZFt8Q/bh0vMBgbs2nfA/oVRk8RWh5fIVadC0ocjhKahO6QkZmlDQLKssWDHUBJSqjutCVTJlkvWfq3ieISxlGavYEcx99vycbyMExcOsl2kNetxNcd6hHNCJjsRaRJQd3TGzjsFYw8/nRwa1TacUts4Y7ni1QvObOdcGu4Hla8roGqAFr6vrPrZqs/I2ehTr4WT ix_vMX_key_pair_Jan7_Khalid"

set groups global system services ssh

set groups global system syslog user * any emergency

set groups global system syslog file messages any notice

set groups global system syslog file messages authorization info

set groups global system syslog file interactive-commands interactive-commands any

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set chassis fpc 0 pic 0 tunnel-services bandwidth 1g

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.114.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn traceoptions file VmxIPSECCommunity

set services ipsec-vpn traceoptions file size 10m

set services ipsec-vpn traceoptions file files 2

set services ipsec-vpn traceoptions level all

set services ipsec-vpn traceoptions flag all

set services ipsec-vpn establish-tunnels immediately

set services ipsec-vpn disable-natt

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.114.92

 

root@Juniper-vMX-Wanclouds> show services ipsec-vpn ipsec security-associations 

Service set: IPSEC-SITE-TO-SITE, IKE Routing-instance: DATAPLANE-VMX-VPN-WANCLOUDS

 

  Rule: IPSec-VYATTA, Term: 1, Tunnel index: 1

  Local gateway: 10.0.10.12, Remote gateway: 108.1.114.92

  IPSec inside interface: si-0/0/0.1, Tunnel MTU: 1500

  UDP encapsulate: Disabled, UDP Destination port: 0

  

  --- No IPSec SA information available ---

 

root@Juniper-vMX-Wanclouds> show interfaces terse | match si 

esi                     up    up

lsi                     up    up

 

 

 

root@Juniper-vMX-Wanclouds> show chassis hardware detail 

Hardware inventory:

Item             Version  Part number  Serial number     Description

Chassis                                VM5A5406B749      VMX

Midplane        

Routing Engine 0                                         RE-VMX

  vtbd0     0 MB                                         Hard Disk

CB 0                                                     VMX SCB

CB 1                                                     VMX SCB

FPC 0                                                    Virtual FPC

  CPU            Rev. 1.0 RIOT         BUILTIN          

  MIC 0                                                  Virtual

    PIC 0                 BUILTIN      BUILTIN           Virtual

 

 

 

root@Juniper-vMX-Wanclouds> show services ipsec-vpn ike security-associations            

 

root@Juniper-vMX-Wanclouds> monitor traffic interface ge-0/0/0 matching udp 

verbose output suppressed, use <detail> or <extensive> for full protocol decode

Address resolution is ON. Use <no-resolve> to avoid any reverse lookup delay.

Address resolution timeout is 4s.

Listening on ge-0/0/0, capture size 96 bytes

 

Reverse lookup for 10.0.10.12 failed (check DNS reachability).

Other reverse lookup failures will not be reported.

Use <no-resolve> to avoid reverse lookups on IP addresses.

 

00:54:04.606186  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:54:04.707330 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

00:54:44.094174  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:54:44.200468 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

00:55:24.234474  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:55:24.328674 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

00:56:04.807564  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:56:04.908874 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

00:56:44.502941  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:56:44.602296 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

00:57:24.887299  In IP 108.1.114.92.isakmp > 10.0.10.12.isakmp: isakmp: phase 1 I ident: [|sa]

00:57:25.005052 Out IP truncated-ip - 70 bytes missing! 10.0.10.12.isakmp > 108.1.114.92.isakmp: isakmp: phase 2/others R inf: [|n]

^C

92 packets received by filter

0 packets dropped by kernel

 

root@Juniper-vMX-Wanclouds> show interfaces terse | grep ge 

ge-0/0/0                up    up

ge-0/0/0.0              up    up   inet     10.0.10.12/24   

ge-0/0/1                up    up

ge-0/0/1.0              up    up   inet     10.0.20.81/24   

ge-0/0/2                up    down

ge-0/0/3                up    down

ge-0/0/4                up    down

ge-0/0/5                up    down

ge-0/0/6                up    down

ge-0/0/7                up    down

ge-0/0/8                up    down

ge-0/0/9                up    down

 

root@Juniper-vMX-Wanclouds> show interfaces terse | grep si    

esi                     up    up

lsi                     up    up

 

 

 

 

Brocade-Vyatta:

=============

 

vyatta@gw-melbourne1-02-06-2016:~$ show configuration commands | grep vpn

set vpn ipsec esp-group ESP-1H compression 'disable'

set vpn ipsec esp-group ESP-1H lifetime '27000'

set vpn ipsec esp-group ESP-1H mode 'tunnel'

set vpn ipsec esp-group ESP-1H pfs 'dh-group5'

set vpn ipsec esp-group ESP-1H proposal 1 encryption '3des'

set vpn ipsec esp-group ESP-1H proposal 1 hash 'md5'

set vpn ipsec ike-group IKE-1H lifetime '28800'

set vpn ipsec ike-group IKE-1H proposal 1 dh-group '5'

set vpn ipsec ike-group IKE-1H proposal 1 encryption '3des'

set vpn ipsec ike-group IKE-1H proposal 1 hash 'md5'

set vpn ipsec ipsec-interfaces interface 'bond1'

set vpn ipsec nat-traversal 'enable'

set vpn ipsec site-to-site peer 34.218.101.112 authentication id '108.1.114.92'

set vpn ipsec site-to-site peer 34.218.101.112 authentication mode 'pre-shared-secret'

set vpn ipsec site-to-site peer 34.218.101.112 authentication pre-shared-secret 'cisco1000'

set vpn ipsec site-to-site peer 34.218.101.112 authentication remote-id '10.0.10.12'

set vpn ipsec site-to-site peer 34.218.101.112 connection-type 'initiate'

set vpn ipsec site-to-site peer 34.218.101.112 default-esp-group 'ESP-1H'

set vpn ipsec site-to-site peer 34.218.101.112 ike-group 'IKE-1H'

set vpn ipsec site-to-site peer 34.218.101.112 local-address '108.1.114.92'

set vpn ipsec site-to-site peer 34.218.101.112 tunnel 0 allow-nat-networks 'disable'

set vpn ipsec site-to-site peer 34.218.101.112 tunnel 0 allow-public-networks 'disable'

set vpn ipsec site-to-site peer 34.218.101.112 tunnel 0 local prefix '192.168.100.0/24'

set vpn ipsec site-to-site peer 34.218.101.112 tunnel 0 remote prefix '10.0.20.0/24'

vyatta@gw-melbourne1-02-06-2016:~$ 

vyatta@gw-melbourne1-02-06-2016:~$ 

vyatta@gw-melbourne1-02-06-2016:~$ 

vyatta@gw-melbourne1-02-06-2016:~$ show vpn ike sa

Peer ID / IP                            Local ID / IP               

------------                            -------------

34.218.101.112                          108.1.114.92                           

 

    State  Encrypt  Hash  D-H Grp  NAT-T  A-Time  L-Time

    -----  -------  ----  -------  -----  ------  ------

    init   n/a      n/a   n/a      no     0       28800  

 

 

vyatta@gw-melbourne1-02-06-2016:~$ show vpn ipsec sa

Peer ID / IP                            Local ID / IP               

------------                            -------------

34.218.101.112                          108.1.114.92                           

 

    Tunnel  State  Bytes Out/In   Encrypt  Hash  NAT-T  A-Time  L-Time  Proto

    ------  -----  -------------  -------  ----  -----  ------  ------  -----

    0       down   n/a            n/a      n/a   no     0       27000   all

 

 

vyatta@gw-melbourne1-02-06-2016:~$

Hi Syed,

 

Still si-* interface is not created on your VMX box.  Please share <show configuration chassis>

 

vmx> show interfaces terse | match si 

esi up up
lsi up up

 

Above is output is not si-* interface.

 

vmx# set chassis fpc 0 pic 0 inline-services

[edit]
vmx# commit
commit complete

[edit]
vmx# run show interfaces terse | match si-
si-0/0/0 up up 

[edit]

 

Hope this helps

--------------------------------------------------------------------------------------------------------
If this post was helpful, please mark this post as an "Accepted Solution".
Kudos are always appreciated!
--------------------------------------------------------------------------------------------------------

Hi,

As I said earlier, you don’t have si-0/0/0 interface configured in your box.
Can you try with below command and check?

root@PE1_re> show interfaces terse | match si
esi up up
lsi up up
lsi.1 up up inet

root@PE1_re>
[edit]
root@PE1_re# set chassis fpc 0 pic 0 inline-services

[edit]
root@PE1_re# commit
commit complete

[edit]
root@PE1_re#
root@PE1_re# run show interfaces terse | match si
si-0/0/0 up up
esi up up
lsi up up
lsi.1 up up inet

[edit]
root@PE1_re#

Regards
Harpreet

I Had  the configuration for Si interfaces the only thing missing was "set chassis fpc 0 pic 0 inline-services" and its working now special thanks to Kingsman (Harpreet) and vvadivel.

 

 

root@Juniper-vMX-Wanclouds> show configuration | display set 

set version 17.2R1.13

set groups global system host-name Juniper-vMX-Wanclouds

set groups global system login user jnpr uid 2000

set groups global system login user jnpr class super-user

set groups global system services ssh

set groups global system syslog user * any emergency

set groups global system syslog file messages any notice

set groups global system syslog file messages authorization info

set groups global system syslog file interactive-commands interactive-commands any

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set chassis fpc 0 pic 0 tunnel-services bandwidth 1g

set chassis fpc 0 pic 0 inline-services

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.114.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn traceoptions file VmxIPSECCommunity

set services ipsec-vpn traceoptions file size 10m

set services ipsec-vpn traceoptions file files 2

set services ipsec-vpn traceoptions level all

set services ipsec-vpn traceoptions flag all

set services ipsec-vpn establish-tunnels immediately

set services ipsec-vpn disable-natt

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.114.92

                                        

root@Juniper-vMX-Wanclouds> show interfaces terse | match si 

si-0/0/0                up    up

si-0/0/0.0              up    up  

si-0/0/0.1              up    up   inet    

si-0/0/0.2              up    up   inet    

esi                     up    up

lsi                     up    up

 

 

Regards

syed.

This message was posted by a user wishing to remain anonymous

Hi fsyed,
Good day 

I have installed Vmax version 18.2R1.9 and used this command "set chassis fpc 0 pic 0 inline-services" but still not showing the si- interface, VCP ram, and cpu already increases . Please help .

BR
sayed

Original Message:
Sent: 03-03-2018 13:18
From: fsyed
Subject: IPsec VPN on Juniper vMX not working .

I Had  the configuration for Si interfaces the only thing missing was "set chassis fpc 0 pic 0 inline-services" and its working now special thanks to Kingsman (Harpreet) and vvadivel.

 

 

root@Juniper-vMX-Wanclouds> show configuration | display set 

set version 17.2R1.13

set groups global system host-name Juniper-vMX-Wanclouds

set groups global system login user jnpr uid 2000

set groups global system login user jnpr class super-user

set groups global system services ssh

set groups global system syslog user * any emergency

set groups global system syslog file messages any notice

set groups global system syslog file messages authorization info

set groups global system syslog file interactive-commands interactive-commands any

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set chassis fpc 0 pic 0 tunnel-services bandwidth 1g

set chassis fpc 0 pic 0 inline-services

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.114.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn traceoptions file VmxIPSECCommunity

set services ipsec-vpn traceoptions file size 10m

set services ipsec-vpn traceoptions file files 2

set services ipsec-vpn traceoptions level all

set services ipsec-vpn traceoptions flag all

set services ipsec-vpn establish-tunnels immediately

set services ipsec-vpn disable-natt

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.114.92

                                        

root@Juniper-vMX-Wanclouds> show interfaces terse | match si 

si-0/0/0                up    up

si-0/0/0.0              up    up  

si-0/0/0.1              up    up   inet    

si-0/0/0.2              up    up   inet    

esi                     up    up

lsi                     up    up

 

 

Regards

syed.

Hi fsyed,
Good day 

I have installed Vmax version 18.2R1.9 and used this command "set chassis fpc 0 pic 0 inline-services" but still not showing the si- interface, VCP ram, and cpu already increases . Please help .

BR
sayed

------------------------------
mamdud sayed
------------------------------

Original Message:
Sent: 03-03-2018 13:18
From: fsyed
Subject: IPsec VPN on Juniper vMX not working .

I Had  the configuration for Si interfaces the only thing missing was "set chassis fpc 0 pic 0 inline-services" and its working now special thanks to Kingsman (Harpreet) and vvadivel.

 

 

root@Juniper-vMX-Wanclouds> show configuration | display set 

set version 17.2R1.13

set groups global system host-name Juniper-vMX-Wanclouds

set groups global system login user jnpr uid 2000

set groups global system login user jnpr class super-user

set groups global system services ssh

set groups global system syslog user * any emergency

set groups global system syslog file messages any notice

set groups global system syslog file messages authorization info

set groups global system syslog file interactive-commands interactive-commands any

set groups global interfaces fxp0 unit 0 family inet address 10.0.254.223/24

set groups global interfaces ge-0/0/0 unit 0 family inet address 10.0.10.12/24

set groups global interfaces ge-0/0/1 unit 0 family inet address 10.0.20.81/24

set groups global interfaces si-0/0/0 unit 0

set groups global interfaces si-0/0/0 unit 1 family inet

set groups global interfaces si-0/0/0 unit 1 service-domain inside

set groups global interfaces si-0/0/0 unit 2 family inet

set groups global interfaces si-0/0/0 unit 2 service-domain outside

set groups global routing-options static route 0.0.0.0/0 next-hop 10.0.254.1

set groups global routing-options static route 0.0.0.0/0 retain

set groups global routing-options static route 0.0.0.0/0 no-readvertise

set apply-groups global

set system root-authentication encrypted-password "$6$bVjvwR9a$fVRP/hbL8YGMmDjlU/ez1uqaogl9XPTrHo3dVHc2iPxwb1tcdUle1j.aOcVc2TGPIkr.EAoFHPz6oCXkb0E271"

set chassis fpc 0 pic 0 tunnel-services bandwidth 1g

set chassis fpc 0 pic 0 inline-services

set services service-set IPSEC-SITE-TO-SITE next-hop-service inside-service-interface si-0/0/0.1

set services service-set IPSEC-SITE-TO-SITE next-hop-service outside-service-interface si-0/0/0.2

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway 10.0.10.12

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-options local-gateway routing-instance DATAPLANE-VMX-VPN-WANCLOUDS

set services service-set IPSEC-SITE-TO-SITE ipsec-vpn-rules IPSec-VYATTA

set services ipsec-vpn rule IPSec-VYATTA term 1 from source-address 10.0.20.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 from destination-address 192.168.100.0/24

set services ipsec-vpn rule IPSec-VYATTA term 1 then remote-gateway 108.1.114.92

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ike-policy IKE-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then dynamic ipsec-policy IPSec-Policy-Vyatta

set services ipsec-vpn rule IPSec-VYATTA term 1 then initiate-dead-peer-detection

set services ipsec-vpn rule IPSec-VYATTA match-direction input

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta protocol esp

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta authentication-algorithm hmac-md5-96

set services ipsec-vpn ipsec proposal IPSEC-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta perfect-forward-secrecy keys group5

set services ipsec-vpn ipsec policy IPSec-Policy-Vyatta proposals IPSEC-Proposal-Vyatta

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-method pre-shared-keys

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta dh-group group5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta authentication-algorithm md5

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta encryption-algorithm 3des-cbc

set services ipsec-vpn ike proposal IKE-Proposal-Vyatta lifetime-seconds 86400

set services ipsec-vpn ike policy IKE-Policy-Vyatta proposals IKE-Proposal-Vyatta

set services ipsec-vpn ike policy IKE-Policy-Vyatta pre-shared-key ascii-text "$9$EVryrvdVYoZjlKYo"

set services ipsec-vpn traceoptions file VmxIPSECCommunity

set services ipsec-vpn traceoptions file size 10m

set services ipsec-vpn traceoptions file files 2

set services ipsec-vpn traceoptions level all

set services ipsec-vpn traceoptions flag all

set services ipsec-vpn establish-tunnels immediately

set services ipsec-vpn disable-natt

set routing-options static route 192.168.100.0/24 next-hop si-0/0/0.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS instance-type virtual-router

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface ge-0/0/0.0

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS interface si-0/0/0.2

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 0.0.0.0/0 next-hop 10.0.10.1

set routing-instances DATAPLANE-VMX-VPN-WANCLOUDS routing-options static route 192.168.100.0/24 next-hop 108.1.114.92

                                        

root@Juniper-vMX-Wanclouds> show interfaces terse | match si 

si-0/0/0                up    up

si-0/0/0.0              up    up  

si-0/0/0.1              up    up   inet    

si-0/0/0.2              up    up   inet    

esi                     up    up

lsi                     up    up

 

 

Regards

syed.