vMX
vMX

how to check interface queue statistic in MX150(VMX)

3 weeks ago

We have deploied a pair of MX150 as WAN routers and we want to check interface queue statistics. But there is no such statistic at all, do you have experience and could shed some light on this? thanks for your great help!

 

lab@r1# run show interfaces queue ge-0/0/1
Egress queue statistics are not applicable to this interface.

 

lab@r1# run show interfaces ge-0/0/1 extensive
Physical interface: ge-0/0/1, Enabled, Physical link is Up
Interface index: 141, SNMP ifIndex: 520, Generation: 144
Description: L2MON_MPLS_LC_CT_WuhanCTVPN52260K_100M
Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, Speed: 1000mbps, Duplex: Full-Duplex, BPDU Error: None, Loop Detect PDU Error: None,
Ethernet-Switching Error: None, MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled, Flow control: Enabled, Auto-negotiation: Enabled,
Remote fault: Online
Pad to minimum frame size: Disabled
Device flags : Present Running
Interface flags: SNMP-Traps Internal: 0x4000
Link flags : None
CoS queues : 8 supported, 8 maximum usable queues
Hold-times : Up 0 ms, Down 0 ms
Damping : half-life: 0 sec, max-suppress: 0 sec, reuse: 0, suppress: 0, state: unsuppressed
Current address: 80:7f:f8:11:17:27, Hardware address: 80:7f:f8:11:17:27
Last flapped : 2019-11-23 08:44:35 CST (07:12:49 ago)
Statistics last cleared: Never
Traffic statistics:
Input bytes : 356174577 71024 bps
Output bytes : 1295588798 1521336 bps
Input packets: 1310454 58 pps
Output packets: 2954978 261 pps
IPv6 transit statistics:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Dropped traffic statistics due to STP State:
Input bytes : 0
Output bytes : 0
Input packets: 0
Output packets: 0
Input errors:
Errors: 0, Drops: 0, Framing errors: 0, Runts: 0, Policed discards: 0, L3 incompletes: 0, L2 channel errors: 0, L2 mismatch timeouts: 0, FIFO errors: 0,
Resource errors: 0
Output errors:
Carrier transitions: 3, Errors: 0, Drops: 0, Collisions: 0, Aged packets: 0, FIFO errors: 0, HS link CRC errors: 0, MTU errors: 0, Resource errors: 0
Active alarms : None
Active defects : None
PCS statistics Seconds
Bit errors 0
Errored blocks 0
Ethernet FEC statistics Errors
FEC Corrected Errors 0
FEC Uncorrected Errors 0
FEC Corrected Errors Rate 0
FEC Uncorrected Errors Rate 0
MAC statistics: Receive Transmit
Total octets 380223186 1348439646
Total packets 1311347 2955019
Unicast packets 1307050 2954058
Broadcast packets 0 22
Multicast packets 4297 939
CRC/Align errors 0 0
FIFO errors 0 0
MAC control frames 0 0
MAC pause frames 0 0
Oversized frames 0
Jabber frames 0
Fragment frames 0
VLAN tagged frames 0
Code violations 0
Total errors 0 0
Filter statistics:
Input packet count 0
Input packet rejects 0
Input DA rejects 0
Input SA rejects 0
Output packet count 0
Output packet pad count 0
Output packet error count 0
CAM destination filters: 1, CAM source filters: 0
Autonegotiation information:
Negotiation status: Complete
Link partner:
Link mode: Full-duplex, Flow control: Symmetric, Remote fault: OK, Link partner Speed: 1000 Mbps
Local resolution:
Flow control: Symmetric, Remote fault: Link OK
Packet Forwarding Engine configuration:
Destination slot: 0 (0x00)
CoS information:
Direction : Output
CoS transmit queue Bandwidth Buffer Priority Limit
% bps % usec
0 be 35 35000000 r 0 low none
1 af 30 30000000 r 0 low none
2 Lync-voice 30 30000000 r 0 strict-high none
3 nc 5 5000000 r 0 low none
Interface transmit statistics: Disabled

1 REPLY 1
vMX

Re: how to check interface queue statistic in MX150(VMX)

3 weeks ago

Hi chenjiang,

 

Believe that's supported in IQ2 PICs.  Please see: 

https://www.juniper.net/documentation/en_US/junos/topics/reference/command-summary/show-interfaces-q...

 

Hope this helps.

Regards,
-r.

--------------------------------------------------

If this solves your problem, please mark this post as "Accepted Solution."
Kudos are always appreciated Smiley Happy.